Dremel 9901 Wolframkarbid-Schnitzbohrer, 1/8 Zoll (3,2 mm) Durchmesser, rotierendes Schnitz- und Gravurzubehör, Fräser (1 Stück), Silber

Brand:Dremel

3.7/5

25.73

PRODUKTBESCHREIBUNG Rain Bird PRF07530S Tropfbewässerungsfilter mit 30 PSI Druckregulierung, 3/4 Außengewinde. Schützen Sie Ihre nachgeschalteten Tropfbewässerungskomponenten mit dieser professionellen, kompakten Einheit, die Filterung und Druckregulierung in einem Stück vereint. Durch Reduzierung der Anzahl der Komponenten in einer Kontrollzone; In einen Ventilkasten passen mehrere Komponenten. Da weniger Verbindungen erforderlich sind, ist die Installation einfacher und schneller. Weniger Teile und weniger Gewindeverbindungen bedeuten auch eine geringere Wahrscheinlichkeit eines Lecks bei der Installation und über die gesamte Lebensdauer des Systems. Die Filtereinheit reguliert den Druck auf 30 psi und die Kappe mit O-Ring-Dichtung lässt sich abschrauben, um einen einfachen Zugang zum 200-Mesh-Filterelement zum Reinigen zu ermöglichen. Das robuste Gehäuse und die Kappe sind aus glasfaserverstärktem Polypropylen gefertigt und bieten eine hohe Robustheit und einen Nenndruck von 150 psi. Funktioniert mit allen Ventilen und wird mit einem vorinstallierten 200 Mesh (75 Mikron) Edelstahlsieb geliefert. Spezifikationen: 3/4 x 3/4 Außengewinde (MPT) Einlässe; Betriebsbereich 0,20 bis 5,0 Gallonen pro Minute; Eingangsdruck 20 bis 150 psi. Auch erhältlich (separat erhältlich) in 40 psi 1 Modell PRF10040S. Das Ersatzfiltersieb (separat erhältlich) hat die Modellnummer: RBY-200SSMX. Rain Bird „Der intelligente Umgang mit Wasser“. VOM HERSTELLER Rain Bird Corporation ist ein Privatunternehmen, das 1933 während des Agrarbooms in Kalifornien gegründet wurde. Wir gelten als weltweit führender Hersteller und Anbieter von Bewässerungsprodukten und -dienstleistungen. Mit Vertriebsbüros rund um den Globus; Wir bieten über 4.000 wassersparende Bewässerungsprodukte in mehr als 130 Ländern an. Von Anfang an hat Rain Bird das branchenweit umfassendste Sortiment an hochwertigen Bewässerungsprodukten für Bauernhöfe, Golfplätze, Sportarenen, Gewerbebauten und Häuser produziert und angeboten. In den letzten 80 Jahren hat Rain Bird weltweit mehr als 450 Patente erhalten. Einschließlich der ersten für die Bewässerung im Jahr 1935 auf unserem ursprünglichen Sprinkler mit Schlagantrieb (US-Patent Nr. 1.997.901), der die landwirtschaftliche Nahrungsmittelproduktion revolutionierte und weltweit eine neue Ära der Bewässerung einleitete. Im Jahr 1990 wurde dieser ursprüngliche Prallsprinkler von der American Society of Agricultural Engineers zum historischen Wahrzeichen erklärt. Unsere Produkte decken alle Aspekte der Bewässerung ab: Zeitschaltuhren/Steuerungen, versenkbare Rotationssprinkler, versenkbare Sprühkopfsprinkler, Sprinklerdüsen, Bewässerungsventile, Tropfbewässerung, Entwässerung und vieles mehr. Diese Produkte wurden weltweit in den größten und prestigeträchtigsten Projekten zur Bewässerung von Wohn-, Gewerbe-, Landwirtschafts- und Golfplatzanlagen ausgewählt und installiert. Rain Bird engagiert sich für die intelligente Nutzung von Wasser™ und erstreckt sich über die Produkte hinaus auf Bildung, Schulung und Dienstleistungen für die Industrie und die Gemeinschaft. Unser Vermächtnis besteht darin, nur Produkte von höchstem Wert und höchster Qualität zu entwerfen und herzustellen. Wir sind dankbar, dass wir von vielen unserer geschätzten Partner zahlreiche Anerkennungspreise erhalten haben. Rain Bird „Der intelligente Umgang mit Wasser

Zur Verwendung mit rotierenden Werkzeugen, die eine Schaftgröße von 1/8 aufnehmen können. Was ist im Lieferumfang enthalten: 1/8 Wolframcarbid-Schnitzbit (x1). Die Zylinderform des Schnitzbohrers ermöglicht einen tiefen Materialabtrag, schneidet flache Bereiche, runde Kanten und führt Stoppschnitte und V-Schnitte durch. Ideal für Projekte wie Metall- oder Glasgravuren, Steinschnitzereien oder das Entfernen von Graten aus Gussteilen. Die äußerst langlebigen Wolframcarbid-Schnitzbits von Dremel können für aggressivere Anwendungen zum Formen, Glätten oder Schleifen harter Materialien wie Metalle, gehärteter Stahl, Feuerkeramik, Gusseisen, Kunststoffe und Harthölzer verwendet werden. Importiert. metallisch.
Batteries Included? ‎No
Batteries Required? ‎No
Brand Dremel
Color ‎Silver
Customer Reviews 4.7 4.7 out of 5 stars 743 ratings 4.7 out of 5 stars
Included Components ‎Unit^Instruction Guide
Is Discontinued By Manufacturer ‎No
Item model number ‎9901
Item Package Quantity ‎1
Item Weight 10 Grams
Item Weight ‎0.353 ounces
Manufacturer ‎Dremel
Material Tungsten Carbide
Material ‎Tungsten Carbide
Measurement System ‎Metric
National Stock Number ‎3455-01-308-4389
Part Number ‎9901
Power Source ‎Corded-electric
Product Dimensions ‎1.6 x 0.8 x 0.2 inches
Size Pack of 1
Size ‎Pack of 1
Warranty Description ‎No

3.7

13 Review
5 Star
79
4 Star
13
3 Star
6
2 Star
1
1 Star
2

Schreiben Sie eine Bewertung

Ihre E-Mail wird nicht veröffentlicht. Alle Pflichtfelder sind mit gekennzeichnet*

Scritto da: AJ
Did exactly what I needed it to.
I used it to widen a hole on tempered steel. Works great.
Scritto da: chris.w.
Cleared right through a steel bolt and aluminum casing.
Allowed me to "drill" out a sheared-off M6 bolt and enlarger the hole for a threaded repair insert. Cleared through the steel bolt and aluminum casing with minimal effort. Will buy it again when this one dulls out.
Scritto da: Pat
Great tool
Cuts very well doesn't break if used properly. I trimmed 1/8 inch steel with it no problems.
Scritto da: Lady Chozens~
Worked!
Perfect for my use!
Scritto da: Robert Retford
Quality tool
Quality tool at a good price
Scritto da: Benny
Good sharp cutter for mild steel but very brittle
I bought this cutter to make a square hole in a metal stud - the type of metal studs used to hold up drywall in high-rise apartments/offices. The cutter worked great, it moved through the metal stud no problem. I did however have 2 problems that I'm writing this review so that others can benefit from my experience: 1.) The cutter is relatively short. I was trying to cut metal that was behind some drywall. So the cutter had to be long enough to get through the drywall and through the metal. Because of an obstruction on the wall surface, I had to hold the tool about 1.25" away from the metal. This made it so that only the very tip of the cutter would contact the metal. While it worked I can comment that the tool is very short, so consider you application before buying. 2.) The cutter is very brittle. I actually cracked the shaft of this tool and could not complete my job. Because of my particular use, the cutter was bouncing around a bit in the slot I was cutting. This caused the bit to break. After it broke, i used the remaining portion to try to cut again. It broke a second time. Final recommendations: This cutter is good for controlled cuts in mild metals where you can brace/secure the work and the tool. This tool is not very good for free-hand cutting as I was doing. Make sure that you control the tool well to prevent bouncing and cracking of the bit. I think I will re-try with a thicker-shanked bit. Perhaps 3/8" if I can find one.
Scritto da: Lonewolf
Tungsten carbide endmill
Not much to say, they are endmills in Tungsten carbide. Dremel pricing is too high for tooling like this. Came loose bouncing around in a big box, one of the two I ordered was stuck in bottom flap, ready to fall out. Luckily I received both, was close call.
Scritto da: Barry Wagner
Finished the task
I needed to shape an opening I drilled in the end of a hand railing. I was slightly off center and just needed to round over a bit to center the peg. This bit was perfect for the job and did it well and quick. It easily worked its way through oak. Job done.
Scritto da: WellTrainedMonkey
Cuts hardened metal effortlessly.
I was working on turning an old bastard file into a knife and needed some way to add minor details on the handle. This got the job done and it still holds its edge. One slight disappointment is that I found a tiny chip on one of the cutting edge, but thankfully it does not appear to affect the overall performance. Just not sure at what point that happened. Amazing performance considering the cost. Great bit to have with your dremel. I'm very happy with this bit.
Scritto da: Mike
Quality product
Needed to enlarge coil seat hole in the lower control arms of my resto. This did the trick like butter in less than a minute per hole with my Dremel. I had my doubts before purchasing, but proved unwarranted. Very pleased. Good durable product. As advertised.
Scritto da: Salvador elizalde santos
Empaque resellado, posible engaño
Regrese el artículo, porque se notaba que había sido abierto, y resellado, la etiqueta de dremel la blanca que ponen estaba despegada hacia un lado, y el plastico del empaque se veía irregular de un lado, como que fue resellado por eso la regrese, no me gusta el engaño si desde el inicio explicaran que esta nuevo pero resellado podría haber accedido pero esto me parecía un engaño y eso molesta.
Scritto da: AdrianS
Warning: Made in China
I bought a couple of these, together with some 9904 bits. While the 9904's are made in the US, the 9901 have the dreaded "Made in China" printed on them. After my experience with Chinese "titanium coated" drill bits, I expect that they are no better than the regular multipurpose bits, but at least twice as expensive (which seems to be confirmed by reviews on amazon.com). If you want Chinese cutting bits, you can get them much cheaper elsewhere, instead of paying a premium just for the Dremel logo.
Scritto da: Jody Wright
Performance on metal
I used this cutter with my Dremel to remove excess metal on new door strikes mounted on metal door frames installed with new handles. Now the doors close and lock with perfection.

Verwandte Produkte

Entdecken Sie unser internationales Netzwerk

Wir versenden in 28 Länder, über 200.000 Produkte. Bleiben Sie auf dem Laufenden, abonnieren Sie den Newsletter.

Array