MAGBIT 786.18.0616 MAG786 3/8 Zoll x 18 Zoll Glockenhanger-Bohrer aus Kohlenstoffstahl

Name: MAGBIT 786.18.0616 MAG786 3/8 Zoll x 18 Zoll Glockenhanger-Bohrer aus Kohlenstoffstahl
Brand: MAGBIT
SKU: 0722170786071
Price: 42.81 EUR
Availability: InStock

Brand:MAGBIT

3.3/5

€
42.81

PRODUKTBESCHREIBUNG HOCHKOHLENSTOFFSTAHL-BELLHANGER-BOHRER DES HERSTELLERS MAGBIT 786.18.0616 MAG786 3/8 Zoll x 18 Zoll High Carbon Steel Bellhanger-Bohrer

Menge

in den Warenkorb legen Kaufe jetzt

EAN: 0722170786071

Kategorien Elektro- & Handwerkzeuge, Elektrowerkzeugteile & Zubehör, Bohrmaschinen, Teile & Zubehör, Twist Bits, Bohrer Bits, Jobber-Bohrer,

In der Nähe der Rillenspitze befindet sich ein Fischaugenloch, das das Ziehen des Drahtes erleichtert. In der Nähe der Rillenspitze befindet sich ein Fischaugenloch, das das Ziehen des Drahtes erleichtert. 2 Aussparungen für Verlängerungsschrauben – Bits 5/8 Zoll und mehr. 82-Grad-Punkt für schnellere Starts.

Brand	‎MAGBIT
Customer Reviews	4.4 4.4 out of 5 stars 14 ratings 4.4 out of 5 stars
Cutting Angle String	82 Degrees
Cutting Angle String	‎82 Degrees
Cutting Diameter	none Inches
Cutting Diameter	‎none Inches
Finish	‎Nickel
Finish Type	Nickel
Finish Type	‎Nickel
Item model number	‎786.18.0616
Item Package Quantity	‎1
Item Weight	‎8.8 ounces
Manufacturer	‎Magnus Industries Inc.
Material	Alloy Steel
Material	‎Alloy Steel
Measurement System	‎Inch
Number of Flutes	‎2
Package Dimensions	‎18.9 x 0.8 x 0.8 inches
Part Number	‎786.18.0616
Shank Type	round shank
Shank Type	‎round shank
Surface Recommendation	‎Wood
Tool Flute Type	‎Spiral
Warranty Description	‎Return defective products to place of purchase for exchange or credit. Warranty does not apply to damage caused by abuse, misuse or alteration.

5 Star

4 Star

3 Star

2 Star

1 Star

Schreiben Sie eine Bewertung

Ihre E-Mail wird nicht veröffentlicht. Alle Pflichtfelder sind mit gekennzeichnet^*

Deine Bewertung

Scritto da: Frank H.

????

????

Scritto da: Schatz Family

good bit

works as advertised

Scritto da: Dan S.

Works Well

I needed a long bit to drill through 16 inches of junk/found lumber glued together in a "butcher-block" configuration, to drive a 3/8-inch dowel through for strength. This bit worked well and I'm quite satisfied with the results, though there are a couple of minor caveats. First, the spiral portion of the bit that contains the flutes and lands is quite short and I had to retract the bit several times per hole to clear out the drilling debris. I'm not subtracting points for this because I'd have had to clear the chips even if the bit's flutes/lands were full length, though perhaps not quite so often. Second, the lip relief was longer than I expected and that may have affected the drilling speed. On the other hand, it may have reduced seizing when drilling through hardened areas such as knots. Again, I'm not subtracting points because, all in all, the bit worked well.