Malco C5A2 Impact Power Assisted Crimper

Name: Malco C5A2 Impact Power Assisted Crimper
Brand: Malco
SKU: 0686046547091
Price: 211.84 EUR
Availability: InStock

Brand:Malco

3.4/5

€
211.84

Der Malco Turbo Crimper Impact ist ein einfaches, kompaktes Zubehörteil, das ausschließlich mit der Kraftunterstützung der Schlagschraubertechnologie arbeitet, um verzinkte Rundrohre (0,31 bis 0,61 mm) mit 30 bis 24 Gauge (0,41 bis 0,71 mm) sicher und effizient zu quetschen Ofenrohr. Der Turbo-Crimper-Aufprall erfordert keine Einrichtung oder Einstellung. Befestigen Sie einfach die 1/4-Zoll-Power-Nut-Antriebswelle an Ihrem Akku- oder Kabel-Schlagschrauber (min. 12 Volt Gleichstrom / max. 7 Ampere Wechselstrom), um sofort mit dem Crimpen verschiedener Größen, Arten und Stärken von Rohren und Leitungen, einschließlich Spiralrohren, zu beginnen. schnell und einfach. Wenn sich die Rohr- oder Kanalnaht in der geschlossenen Position befindet, beginnen Sie mit dem Crimpen auf einer Seite der Naht, indem Sie vorsichtig am Auslöser des Schraubendrehers ziehen und den Turbo-Crimper-Schlag auf die Metallkante richten. Führen Sie die Crimpzange kontrolliert um den Rohrumfang herum und winkeln Sie die Crimpzange dann vom Metall ab, während sich die Crimpzange der anderen Seite der Naht nähert. Die Wirkung des Turbo-Crimpwerkzeugs ist fünfmal schneller als bei einem manuellen Crimpwerkzeug, basierend auf tatsächlichen Feldversuchen! Es ist für jeden Bediener bequem zu manövrieren und, Linkshänder beachten, es funktioniert mit dem Schlagschrauber im Vorwärts- oder Rückwärtsgang. Die handliche kleine Turbo-Bördelzange Impact ist ein unverzichtbares Zubehör für jeden HVAC-Installateur und lässt sich bei Nichtgebrauch problemlos in einer Werkzeugtasche oder Tasche verstauen.

Menge

in den Warenkorb legen Kaufe jetzt

EAN: 0686046547091

Kategorien Werkzeuge & Heimwerken, Elektro- & Handwerkzeuge, Handwerkzeuge, Crimpzangen,

Lässt sich in einem Beutel oder einer Tasche verstauen. Kompakt, leicht zu manövrieren und auszubalancieren. Keine Einrichtung oder Anpassung. Crimps 30-24 ga. (0,41-0,71 mm) runder Metallkanal. Verwandelt Ihren Schlagschrauber schnell in eine elektrische Crimpzange.

Batteries Included?	‎No
Batteries Required?	‎No
Brand	Malco
Brand	‎Malco
Color	Black
Color	‎Black
Country of Origin	‎USA
Customer Reviews	4.4 4.4 out of 5 stars 662 ratings 4.4 out of 5 stars
Grip Type	‎Ergonomic
Handle Material	Metal
Handle Material	‎Metal
Is Discontinued By Manufacturer	‎No
Item Dimensions LxWxH	8.25 x 6 x 2 inches
Item Dimensions LxWxH	‎8.25 x 6 x 2 inches
Item model number	‎C5A2
Item Package Quantity	‎1
Item Weight	2.1 Pounds
Item Weight	‎2.1 Pounds
Manufacturer	‎Malco Products
Material	‎steel
Measurement System	‎Metric
Part Number	‎C5A2
Power Source	‎Hand Powered
Product Dimensions	‎8.25 x 6 x 2 inches
Style	‎Crimper
Warranty Description	‎Limited

5 Star

4 Star

3 Star

2 Star

1 Star

Schreiben Sie eine Bewertung

Ihre E-Mail wird nicht veröffentlicht. Alle Pflichtfelder sind mit gekennzeichnet^*

Deine Bewertung

Scritto da: Anthony

Absolute wrist saver

I’ve done hvac for over 4 years now hand crimping spiral and snap lock sheet metal and once I bought this my efficiency shot through the roof. Great crimps every single time super easy to use, durable, and easy on your impact great purchase

Scritto da: Kristina Kreitzer

Better than hand crimpers

I’m a union sheet metal worker, and this thing is awesome. A bit of a learning curve l, but once you get the hang of it there’s no turning back. This thing has some weight to it which surprised me at first, but after using it I understand why. I’ve been looking at buying this for about a year, finally pulled the trigger and I’m glad I did. 5 secs is all it takes to crimp a pipe and it’s a close to a factory edge. I stop before the seam afraid to blast through it, though I’m sure it will handle it. Im very happy have to wait to see how long the shank lasts.

Scritto da: Ed

On the pricey side but faster than hand crimping

I was skeptical about buying this because it's not cheap. Hand crimpers are a lot cheaper. But I'm very impressed at how it crimps. It's noisy and you can only use it with a impact. I tried using it with my regular drill and it twisted the pipe and cut my arm so do not use anything but an impact it even has a warning label. But if you're crimping lots of pipe there's no competing with a hand crimper at how fast you can use this. Definitely worth the money if you are made of it.

Scritto da: Scott Messina

Saves your forearms

This is much faster than hand crimping, and far easier on your hands and forearms. I can crimp a 10" duct in about 10 seconds, while it's already mounted. Because this goes on the end of your impact, it can spin 360 to modify duct that's already in the air, as long as you've got 2+ inches all of the way around. Just don't go over a seam, it says so right in the instructions. It takes a few tries to learn the best way to get it fully engaged on the pipe, I just go forward a couple of clicks, then reverse back to the starting point, and it's ready to go. I am using it with a Milwaukee M12 Surge impact, so it's noise level isn't too bad. With a standard impact, it will likely be quite loud, especially when amplified by uninsulated ducting

Scritto da: Jason

Must have? Or nice to have? That’s the question.

It’s quit useful and saves tons of time if your cutting a lot of duct. There is one issue I have come across. I found that using this with fittings, like els, I found the crimp isn’t enough. I need to hand crimp a bit because it’s not quite enough to fit the duct to the fitting. Still worth it and a valuable tool. Is it a must have? I wouldn’t say that. But I’m very happy with it and do recommend it.

Scritto da: Placeholder

Great product

Thus is so fast and saves so much time when installing metal ducting, it’s a great tool

Scritto da: James

Worth it!

If you do much work with round sheet metal ducting this is worth it, in one job I used it so many times I didn’t even think I would need it and it saved so much time, it’s far quicker and results in more professional look than a hand crimper. It takes a little getting used to though but after that it’s awesome

Scritto da: Duct Sealant Joe

Fantastic, but....

Month in and is already wearing out a little bit. Works maybe a little too well. Will over crimp things by a half inch for circular duct. Otherwise it saves my time, and my hands. Would recommend

Scritto da: Tyler little

Beware! Can become a 270$ tool quickly

This thing is awesome! It crimps spiral better than you get from the shop, that being said if you push it too hard or try to crimp over a seam the drive shaft will snap. Malco has you covered though for almost 70$ they will send you a replacement shaft which is little more than a nut driver (10mm I think) with a shoulder at the end to hold it to the tool. If this easily replaceable, and easily broken part was a reasonable price this thing would get 5 stars all day. If you have a friend with a metal lathe maybe you can whittle up a cheaper replacement.

Scritto da: Jeff Arbeau

Forget what you know about crimping! 2ND REVIEW

The media could not be loaded. You have to learn how to use this tool. This crimper is nothing like any way you crimped before. Go low and slow till you ght the fell of it. Wish I had this 20 years ago. I love it!!

Scritto da: Brendon Maclellan

Awesome

This thing save so much time and energy. Love it. Highly recommended

Scritto da: Amazon Customer

Crap

Its crap. It rips apart ductwork and when you are super careful and actually get it to crimp all the way around it doesn't even crimp it enough for it to fit.