SharkBite 3/4 Zoll x 1/2 Zoll Reduzierkupplung, Push-to-Connect Messing-Sanitärarmatur, PEX-Rohr, Kupfer, CPVC, PE-RT, HDPE, U058LFA 3/4 Zoll x 1/2 Zoll

Brand:SharkBite

3.8/5

28.51

PRODUKTBESCHREIBUNG Vereinfachen Sie Ihre Sanitärprojekte mit den SharkBite Crimp-Reduzierkupplungen aus Messing. Diese Rohrkupplungen bestehen aus starkem und stabilem bleifreiem DZR-Messing und sind eine hervorragende Möglichkeit, Rohre einfach zu installieren, ohne dass zusätzliche Werkzeuge, Kleber oder Löten erforderlich sind. Diese Kupplungen können in Nassleitungen eingebaut werden und sind für unterirdische und hinter der Wand liegende Anwendungen ohne Zugangsklappen zugelassen (bei unterirdischer Verlegung ist eine Umhüllung erforderlich). Ausgelegt für 200 psi und 200 °F (93 °C). VOM HERSTELLER SharkBite ist das Steckverbindungssystem, das wirklich greift. Dies ist die einfachste Möglichkeit, Kupfer-, CPVC- oder PEX-Rohre in beliebiger Kombination zu verbinden – ohne Löten, Klemmen, Verbindungen oder Kleber. Führen Sie einfach das Rohr ein, und die Edelstahlzähne greifen und greifen fest, während ein speziell formulierter O-Ring zusammengedrückt wird, um eine perfekte Abdichtung zu schaffen. Ebenso schnell erfolgt die Demontage mit dem einfachen Trennwerkzeug. So können Armaturen und Ventile einfach ausgetauscht und wiederverwendet werden. Sie können nach der Montage sogar gedreht werden, um die Installation in engen Räumen zu erleichtern. Holen Sie sich SharkBite und nehmen Sie Ihr nächstes Sanitärprojekt in den Griff. Diese Armaturen sind bleifrei und erfüllen alle Anforderungen für Sanitärinstallationen in Kalifornien und Vermont.

ZERTIFIZIERT: Die Wasserversorgungskupplung ist für 200 psi und 200 °F (93 °C) ausgelegt. BLEIFREI: Die gerade Kupplung besteht aus starkem und stabilem bleifreiem DZR-Messing. EINFACHE INSTALLATION: Die gerade Kupplung kann einfach installiert werden, ohne dass Löten, Kleben oder zusätzliche Werkzeuge erforderlich sind. kann in Nassleitungen eingebaut werden. VIELSEITIG: SharkBite-Sanitärarmaturen sind mit PEX-, Kupfer-, CPVC-, PE-RT- und SDR-9-HDPE-Rohren kompatibel. Zugelassen für unterirdische und hinter der Wand liegende Anwendungen ohne Zugangsklappen (bei unterirdischer Verlegung ist eine Umhüllung erforderlich). REDUZIERROHRVERBINDER: Rohrverbinder aus Messing eignen sich perfekt für einfache Verbindungen zwischen Rohren gleicher Größe. Ideal für den Einsatz in engen Räumen **Fittings mit großem Durchmesser (1-1/4 bis 2 Zoll) erfordern beim Anschluss an PEX-Rohre eine Versteifung (separat erhältlich)**.
Batteries Included? ‎No
Batteries Required? ‎No
Brand SharkBite
Brand ‎SharkBite
Color Brass
Color ‎Brass
Connector Type Reducer
Connector Type ‎Reducer
Country of Origin ‎China
Customer Reviews 4.8 4.8 out of 5 stars 1,138 ratings 4.8 out of 5 stars
Exterior Finish Brass
Exterior Finish ‎Brass
Included Components ‎Fitting
Is Discontinued By Manufacturer ‎No
Item Dimensions LxWxH 7 x 5 x 2 inches
Item Dimensions LxWxH ‎7 x 5 x 2 inches
Item model number ‎U058LFA
Item Package Quantity ‎1
Item Weight 2.24 Ounces
Item Weight ‎2.24 Ounces
Manufacturer ‎Cash Acme
Material Brass
Material ‎Brass
Measurement System ‎inch
Number Of Pieces 1
Number Of Pieces ‎1
Part Number ‎U058LFA
Product Dimensions ‎7 x 5 x 2 inches
Size 3/4 in. x 1/2 in.
Size ‎3/4 in. x 1/2 in.
Style ‎Brass Push Reducing Coupling
Thread Type NPT
Thread Type ‎NPT
Warranty Description ‎Lifetime

3.8

11 Review
5 Star
85
4 Star
10
3 Star
2
2 Star
1
1 Star
2

Schreiben Sie eine Bewertung

Ihre E-Mail wird nicht veröffentlicht. Alle Pflichtfelder sind mit gekennzeichnet*

Scritto da: Justin Zachary Wanke
Works how a SharkBite is supposed to!
Works how a SharkBite is supposed to!
Scritto da: Adam H.
Super easy to use in tight spots
I have a 1/2 inch hose bib I wanted more water to. So I ripped out the existing plumbing and replaced it with 1inch and 3/4 inch CPVC. The hose bib was in a spot where it was hard to get to. I had to transition from 3/4 to 1/2 inch in a spot I could not reach with a torch or CPVC glue very well. This joined the two materials nicely. It leaked a little, but that is because I did not have it fully pushed in to the stop. Once I got it fully pushed in it stopped leaking. I just have a hard time thinking this will last long term. I have two in use both in areas of my basement that are exposed ceilings, but drywalled walls, so a leak could be serious. In one area I think I am going to take this out where I can get to it and make a more permanent threaded male CPVC to female sweated copper just to be 100% sure of the connection. The other one is near a floor drain and harder to get to so I am going to leave that one alone. All in all I would recommend these for exposed areas, if you are in a hurry to get water back on, or if the fitting is in an area hard to reach with a torch, glue, or PEX crimp tool. I wish I would have known you can remove the PEX guides from the fitting with a fitting removal tool and a needle nose pliers. I would have done that hopefully resulting in more unimpeded water flow. I would buy again and if they last 25 years like the MFG warrantees them for then they are a great solution. The hose bibs and therefore the shark bites will be changed out before 25 years go by.
Scritto da: Little Shepherd
Sharkbite Fittings Review
These fittings are the easiest I've ever used. Just push them all the way on and you're done! Of course I always check for leaks but so far I haven't had a single night ne leak and I've used more than a dozen of these Sharkbite Fittings on different projects of mine and when helping other people out. If all plumbing in the world was this easy everyone would be doing it. Good quality at a decent price.
Scritto da: Jim
I hate plumbing
I’m not a plumber and I hate doing a job turning on the water and discover one or more leaks. If you install these the way the manufacturer says you will will save time and headaches. Sure they cost a little more but remember time is money. For me these reduced the cursing, helped my marriage and allowed more time for a few cold ones after the job.
Scritto da: JDS
Works great
Use several different sharkbits and they all work great. Just make sure you measure and mark the tubing before insertions so you are sure the tub is completely inserted.
Scritto da: Nicholas
Shark bites are The bees knees
Anyone can be a plumber thanks to shark bite. Ever since I started using shark bite, I can sleep soundly at night !
Scritto da: Gwhunter
Amazon Used need to look at items.
First off sharkbites work no issues just wish they didn't cost so much. I bought one new and one used trying to save money. I know sometimes Amazon used is a crap shoot. This was the worst I have ever seen. I think know one even looks at their returns. Check out my picture. It came to me with a piece of copper pipe jammed, twisted, and solder dripping down it like they had no idea about pluming and tried to yank the pipe out but didn't work so they cut it off and sent it back. What a disgrace on Amazons part.
Scritto da: PPMAN
Plumber of 30 years, sharkbyte is the only brand.
Sharkbyte is the highest quality . I have purchased many other cheaper brands and realized the metals used to make them probably will not hold up to hard water very long. I would only want Sharkbyte in my home because they are very well made and long lasting. This is NOT the part to try and save a buck !
Scritto da: Kelly Warrington
Expect the best
Very well made, best fittings on the market. Super easy to use
Scritto da: Jimmy
Worked perfectly
Good quality
Scritto da: Amazon Customer
Great product
Fits perfectly

Verwandte Produkte

Entdecken Sie unser internationales Netzwerk

Wir versenden in 28 Länder, über 200.000 Produkte. Bleiben Sie auf dem Laufenden, abonnieren Sie den Newsletter.

Array