Yost Vises 480 8 Heavy Duty Utility-Kombination aus Rohr- und Schraubstock, Rohr- und Schraubstock, 20,3 cm

Brand:Yost Vises

3.8/5

726.57

Der Mehrzweck-Rohr- und Tischschraubstock der Apprentice-Serie von Yost Vises verfügt über eine um 360 Grad drehbare Basis und lässt sich an einer Werkbank montieren, um eine Klemmwirkung für leichte Anwendungen zu gewährleisten. Die um 360 Grad drehbare Basis mit (2) Arretierungen passt die Richtung der Backen an, um eine korrekte Platzierung zu gewährleisten. Durch handfestes Anziehen des Feststellknopfs an der Basis wird die Position gesichert. Der Schraubstock hat einen Gusseisenkörper mit einer U-Profilstange aus Stahl für eine lange Lebensdauer und verfügt über einen flachen Teil, der als Amboss und zusätzliche Arbeitsfläche dient. Die Oberbacken aus gehärtetem Stahl können bei Verschleiß ausgetauscht werden, und die integrierten Rohrbacken aus Gusseisen sind für besseren Halt gerillt. Durch Drehen des Schraubstockgriffs im oder gegen den Uhrzeigersinn werden die Backen näher zusammen- oder auseinandergefahren.

GARANTIE: Kommt mit einer einjährigen eingeschränkten Garantie und einer 90-tägigen Rückgabefrist. SICHERHEITSHINWEISE: Der Missbrauch von Schraubstöcken kann zu schweren Verletzungen an Augen, Händen und/oder anderen Körperteilen führen. Schraubstöcke müssen ordnungsgemäß aufgestellt und verwendet werden. Lesen, verstehen und befolgen Sie vor der Einrichtung und Verwendung alle Anweisungen im Handbuch. YOST VISES-QUALITÄT: Jedes Yost Vises-Werkzeug ist so konstruiert, dass es hohe Standards an Qualität, Festigkeit und Haltbarkeit erfüllt. Wir legen Wert auf Qualität statt auf Quantität und stellen Produkte her, die sicher und einfach zu verwenden sind. Zur Unterstützung unserer Qualitätsgarantie bieten wir lebenslangen technischen Support. ANWENDUNG: Stellen Sie sicher, dass der Schraubstock sicher an der Werkbank montiert ist und die Drehbasisverriegelung sicher ist. Öffnen Sie den Schraubstock, indem Sie den Schraubstockgriff gegen den Uhrzeigersinn drehen. Platzieren Sie den Gegenstand zwischen den gezahnten Backen. Schließen Sie den Schraubstock, indem Sie den Schraubstockgriff im Uhrzeigersinn drehen, bis der Gegenstand fest in den gezahnten Backen sitzt. Ziehen Sie ihn weiter fest, bis Sie den Gegenstand nicht mehr bewegen können. Nicht zu fest anziehen, da dies zu Schäden am Gegenstand und/oder am Schraubstock führen kann. Wenn Sie mit der Arbeit am Gegenstand fertig sind, drehen Sie den Schraubengriff gegen den Uhrzeigersinn, um den Gegenstand freizugeben. DREHBASIS: Die um 360 Grad ineinandergreifende (Zahnrad-)Drehbasis mit (2) Arretierungen passt die Richtung der Backen an, um eine korrekte Platzierung zu gewährleisten. Basismontagelaschen: (4) x 11/16 (Montagematerial nicht im Lieferumfang enthalten). TECHNISCHE DATEN: Backenbreite: 8,0 x Backenöffnung: 7,50 x Ausladungstiefe: 4,5 Zoll; Rohrkapazität: 1/8 x 3 Durchmesser, Rohrbacken sind eingegossen; 0,67 Zoll T x 10,4 Zoll langer Griff mit Gummipuffern; 4. 13" x 3. 63" Schlagfläche. KOMBINATIONSSCHRAUBSTOCK: Der Yost Vises 480 8-Zoll-Kombi-Rohr- und Bankschraubstock besteht aus einem 30.000 PSI-Gussgrauguss mit einer U-Profilstange aus Stahl. Ausgestattet mit einer großen Amboss-Arbeitsfläche, verfügt es außerdem über austauschbare gezahnte Oberbacken aus gehärtetem Stahl und eine permanent gezahnte Rohrbacke mit großer Rohrkapazität.
Brand Yost Vises
Color Blue
Item Dimensions LxWxH 11 x 11 inches
Item model number 480
Item Weight 80 Pounds
Manufacturer Yost Tools
Material Cast Iron with Steel U Channel Bar
Style Heavy Duty

3.8

13 Review
5 Star
80
4 Star
14
3 Star
4
2 Star
0
1 Star
2

Schreiben Sie eine Bewertung

Ihre E-Mail wird nicht veröffentlicht. Alle Pflichtfelder sind mit gekennzeichnet*

Scritto da: Doug Wade
Very nice vise. A lot more sturdy than I thought it would be
Shipped as advertised. Will last for years. The plastic pieces to fit on the jaws was not in my box.
Scritto da: Mike
Solid, sturdy, and smooth operation. Great vise.
I love this vise. I got the 5.5" one as an upgrade from my previous one which was often too small, or would slip on my workbench. My previous one was the kind that tightens itself on the the workbench but doesn't bolt in. The Yost 455 is the perfect size for my projects and allows me to bolt it down so it's easy to use. Let me share the bolts, washers, and locking nuts you will want to use for mounting this. There is some conflicting information in the Q&A and reviews. If you have a workbench where you can drill through the top, I can say definitively that the best way to mount it is use the base as a template and mark where the holes are in the base. Then use a 1/2" drill bit to drill holes through the tabletop. I used the following hardware which should work for anyone. You'll just need to adjust the bolt length for the width of your tabletop. Bolts: 1/2 in.-13 x 2-1/2 in. Hex Bolt (2.5" was the right length for my tabletop, you made need shorter or longer) Washers: 1/2 in flat washers with a 1 in outer diameter (OD) (1/2" inner diameter) Locking nuts: 1/2 in.-13 Nylon Lock Nut All the mounting hardware set me back about $11 at the local orange colored hardware store. It would have been nice if the hardware was included, but the vise itself is a great value regardless.
Scritto da: John Farrington
Solid and well made.
This is a solid and well made vise. Smooth, easy operation. This should last for years.
Scritto da: Tony
Good Value
I bought this blue Yost 455 Vise about 1 year ago and I am very happy with it. Most of my work is light duty, so I mounted it on a wooden work bench with a 2 x4 frame. For my light duty needs, I used 1/2" hex bolts to minimize 2 x 4 wall thickness loss. I then bought the RUITOOL brand blue colored 5.5" Vise Jaws Nylon Vise Block with Magnetic Soft Jaws, and I'm very happy with these soft jaws too. The Yost 455 and these soft jaws are an excellent match for my bench needs. If using a 2 x 4 frame for vise fastening, think about using a drill press or portable drill guide so that the drilled holes are straight. .
Scritto da: BaronR
No need to spend more
Very sturdy and good features.
Scritto da: Jeff
Vise has all the features of a bench vise.
Fit and function are good, it only weighs about 35 lbs, which means for a 5.5” vise its a bit light. Weight equates to sturdyness when looking at vises. It will work well for my needs.
Scritto da: Mattamuskeet
Poor QC
I tried buying a vise local first at Harbor Freight (HF), but returned due to poor casting and I wasn’t impressed by Home Depot’s offerings. I ordered the Yost 455 after a lot of research. Out of the box, this thing is not the best quality. The jaws do not line up and there is a lot of slop when the jaw is open. It also came with a nick in the metal from the manufacturer. Like the 5” “Central Forge” HF vise, this one is made in China, but at least the jaws lined up with no slop on the HF and it was only $60 compared to $85. Still this one is better in comparison and a decent value. I just wish they still made quality items in the US at a reasonable price because nothing I have bought from China has been what I would describe as 5 star quality.
Scritto da: William A McHale Jr
Great value!
I swore off buying any more garbage from harbor freight and figured that meant paying a lot of money for items like this. Yost company is from MI, USA. I couldn't figure out for sure where this is made but I don't care because I installed and used it today and am extremely happy with it. Build quality, fit and finish look great. Super value.
Scritto da: BL
Awesome tool
This seems to be of great quality for the price. Others I searched for were either too expensive or looked to be of cheap quality. Shown is a picture of it bolted to my workbench. For it's size it can open fairly large and the pipe jaw area is very handy to have as well. Also love the rubber gromets permanently attached to the handle. Rotating function is very useful and locks securely into position.
Scritto da: Aaron D
Great For Light Duty Home Use
Great for light to medium duty. Have this in my garage on a makeshift work bench I made out of an old table that was going to be thrown out. Bolted to table fairly easy with 4 carriage bolts, nuts and washers. Jaws open and close smoothly and hold whatever I am working on very well.
Scritto da: Simon
Good bang for the$
Good quality for the price and company as been around for a while. No it’s not a top brand but it’s a really good starting point that will last you years.
Scritto da: Harywood
A Nice Vice for a Good Price
My son wanted a vice for Christmas. I did some research and aside from the expensive Record vises, the Yost provides good features and performance at an affordable price. He's really happy with it.
Scritto da: Paul
Hapy with my Yost vise
I am very pleased with my Yost vise. Build-quality and precision seem to be very good, and the price was very competitive.

Verwandte Produkte

hot
Yost Vises F10WW Holzschraubstock
3.6/5

€ 168.06

Yost Vises F10WW Holzschraubstock
3.6/5

€ 168.06

Entdecken Sie unser internationales Netzwerk

Wir versenden in 28 Länder, über 200.000 Produkte. Bleiben Sie auf dem Laufenden, abonnieren Sie den Newsletter.

Array