MG Chemicals 426 Entlötgeflecht Nr. 4, feines Geflecht, Superdocht mit RMA-Flussmittel, 5' Länge x 0,1 Breite, Blau

Brand:MG Chemicals

3.7/5

21.28

Überall dort, wo Sie Lötzinn auftragen können, können Sie es mit Super Wick wieder herausnehmen. Entfernen Sie selbst die teuersten Schaltkreise mit Zuversicht. Legen Sie einfach den Super Wick auf die Lötstelle, setzen Sie die Spitze des Lötkolbens eine Sekunde lang auf die Oberseite und heben Sie dann Eisen und Super Wick zusammen an, um eine saubere Verbindung zu erhalten, die zum Entfernen oder Ersetzen von Komponenten bereitsteht. Super Wick besteht aus reinem Kupfer, speziell gewebt und auf eine Spule im Taschenformat mit unter Druck stehender Peripherie gewickelt. RoHS-konform.

Entwickelt, um einen umweltfreundlichen Rückstand zu hinterlassen. Hergestellt nach SPC-Richtlinien. Es wird ausschließlich reines Kolophonium vom Typ „RMA“ verwendet, das den Anforderungen von MIL-F-14256F (ANSI/J-STD-0004) entspricht. Spulen ohne statische Aufladung. Oxidfreies, sauberes Kupfer.
Country of Origin China
Domestic Shipping Item can be shipped within U.S.
International Shipping This item can be shipped to select countries outside of the U.S.
Is Discontinued By Manufacturer No
Item model number 426
Manufacturer MG Chemicals
Product Dimensions 0.04 x 0.01 x 0.04 inches; 0.25 Ounces

3.7

13 Review
5 Star
77
4 Star
14
3 Star
5
2 Star
1
1 Star
3

Schreiben Sie eine Bewertung

Ihre E-Mail wird nicht veröffentlicht. Alle Pflichtfelder sind mit gekennzeichnet*

Scritto da: Not Today
It Works So Well You'll Feel Like a Professional
This solder wick is like night and day to cheaper alternatives. I used to use cheap solder wick, and never got good results with it. I thought I just didn't know what I was doing. This solder wick clears the solder from through-holes on PCBs with ease! It turned an almost impossible task into an absolute pleasure. I cannot recommend it enough.
Scritto da: NelsonCartier
wow buy these read my review
this is cheap and gets the job done perfect winner lol
Scritto da: Jimmah!
It works
This solder wick works nicely. Nothing else to mention except that I recently saved a lot on my car insurance.
Scritto da: Cbass
Does the jobe
Altho im quite novice a solderer, so idk
Scritto da: David M.
Stuff is nice!
I've always used a solder sucker to remove solder from a pcb. But the components are just too small in this situation and the solder wouldn't hold a temp long enough to jam a sucker in there. I was working with SMD chips and had to repair 4 pads. This braid is the way to go, definitely the right tool for the job.
Scritto da: Alfatech
Great way to clean desolder
Great companion for my solder, does a good job cleaning up the solder mess when removing and replacing burst capacitors.
Scritto da: CJEDROK
Great for value
Needed to resolder some connections and I used this to clean up the dirty solder that was left behind. Did a great job on soaking up the solder
Scritto da: KR
Pure Magic!
This stuff is incredible for fine electronics. Quickly sucks up solder completely and with very little heat needed. Much better than my 20 year old Radio Shack copper braid that recently ran out. The incorporated flux really makes difference.
Scritto da: Kuba
Easy to use, cant go wrong.
Always found it so much easier to use desoldering wick than anything else, even a desoldering pump doesnt work as easily for me. Absolutely perfect for small projects, this small reel lasted me for desoldering around 80 mechanical keyboard switches. So around 160 large solder connections. A small warning to those working on PCB's , be sure to heat up the wick well and KEEP THE HEAT APPLIED while you lift it up, otherwise you risk tearing off the pad, damaging your PCB. For the price, especially with next day shipping it is fantastic.
Scritto da: Funko photographer
Did the job nicely
Brought this to desolder some wires and the joysticks from an old PS2 controller circuit board, and it did the job perfectly fine. For my first time desoldering anything, I had the job done in a matter of minutes. If you’re working with circuit boards, you’ll definitely want to clean it afterwards with some rubbing alcohol, as the added flux does make it sticky and quite grubby afterwards.
Scritto da: RB
This really sucks…solder!
I’ve been working with soldered components for some time now. I always seemed to struggle desoldering, but little did I know that the braid I was using was rubbish! Since getting a smaller roll of this, you could literally see the solder drawn off the components and onto the braid. It draws it well beyond the point of the soldering iron. It’s so good I’ve bought this larger roll now, as desoldering is so much easier with this. Highly recommended.
Scritto da: MS
Worked a treat
Was a bit dubious about how good a pre-fluxed wick would be but it did exactly what is was supposed to do and all without any additional flux required at all, a great job, excellent product at a great price.
Scritto da: seaside terminator
Ok for small amount of solder.
I feel it’s ok for de soldering when you are removing very very small blobs of solder as I struggled with removing what I refer to what is normally on a component on a PCB.

Verwandte Produkte

Entdecken Sie unser internationales Netzwerk

Wir versenden in 28 Länder, über 200.000 Produkte. Bleiben Sie auf dem Laufenden, abonnieren Sie den Newsletter.

Array