Armacost Lighting 840600 Pilote à intensité variable 60 W pour éclairage LED, avec cordon AC amovible, éclairage blanc 60 W 12 V

Name: Armacost Lighting 840600 Pilote à intensité variable 60 W pour éclairage LED, avec cordon AC amovible, éclairage blanc 60 W 12 V
Brand: Armacost Lighting
SKU: 0850080006528
Price: 98.86 EUR
Availability: InStock

Brand:Armacost Lighting

3.7/5

€
98.86

Le pilote LED à intensité variable de 60 watts d'Armacost Lighting offre des performances de gradation LED exceptionnelles et un contrôle de la luminosité de qualité architecturale. Bien que pratiquement tous les gradateurs fonctionnent avec ce pilote de LED à intensité variable, Armacost Lighting recommande les gradateurs universels Lutron CFL et Leviton illumatech en raison de leur réglage de plage de gradation bas de gamme. Fournit une gradation fluide, stable et sans scintillement avec un démarrage en douceur et des performances de fondu à l'allumage et de fondu à l'obscurité souhaitables. Lorsqu'un gradateur est réglé sur pleine luminosité, le pilote LED fournit une luminosité totale - il n'y a pas de perte de rendement lumineux haut de gamme. Fil direct. Le conducteur a une protection complète contre l'arrêt de sécurité en cas de surcharge d'éclairage, de circuit ouvert, de court-circuit, de surchauffe ou d'autre défaut, redémarrage automatique après que le défaut a été corrigé. Il s'agit d'une unité d'alimentation de classe 2 pour la sécurité et de classe II AC. entrées, boîtier entièrement isolé, aucun fil de terre n'est requis. Intérieur/extérieur, etc. Répertorié pour une utilisation dans des endroits secs et humides. Pour fonctionner correctement, votre éclairage LED doit fonctionner sur un courant continu de 12 volts et pouvoir être atténué. Ce pilote fonctionne bien avec tous les éclairages à ruban LED 12V DC. Pour les autres types d'éclairage LED, contactez le fabricant pour confirmer que votre éclairage est à intensité variable et qu'il fonctionne sur une alimentation cc de 12 volts.

Montant

Ajouter au panier Acheter maintenant

EAN: 0850080006528

Catégories Outils et amélioration de la maison, Adaptateurs, Éclairage Accessoires, Transformateurs basse tension,

Pas de charge électrique minimale ; la gradation fonctionne aussi bien qu'il s'agisse d'alimenter une seule rondelle lumineuse à DEL de 3 watts ou un éclairage à ruban de 60 watts, ou une combinaison des deux. L'alimentation de classe 2 est dotée d'une protection contre les surcharges et d'un arrêt automatique. Connectez jusqu'à 100% de la charge maximale nominale de 60 watts - la performance de déclassement n'est pas requise. Compatible avec les gradateurs et commandes d'éclairage 120 volts CA et les gradateurs et commandes CC basse tension. Fournit une gradation fluide et complète sans scintillement pour l'éclairage LED 12 volts tels que les bandes LED, les modules, les barres lumineuses, les rondelles et autres lumières d'accentuation LED.

Batteries Included?	‎No
Batteries Required?	‎No
Brand	Armacost Lighting
Capacity Description	‎60 Watt
Certification	‎UL
Color	‎White
Country of Origin	‎China
Current Rating	5 Amps
Customer Reviews	4.7 4.7 out of 5 stars 787 ratings 4.7 out of 5 stars
Included Components	‎60-Watt power supply
Is Discontinued By Manufacturer	‎No
Item Dimensions LxWxH	7.06 x 2.38 x 1.38 inches
Item model number	‎840600
Item Package Quantity	‎1
Item Weight	‎8 ounces
Manufacturer	‎Armacost Lighting
Material	‎Plastic
Mounting Type	Ceiling Mount
Mounting Type	‎Ceiling Mount
Number Of Pieces	‎1
Part Number	‎840600
Pattern	‎Lighting
Plug Format	‎A- US style
Power Source	AC
Power Source	‎AC
Product Dimensions	‎7.06 x 2.38 x 1.38 inches
Shape	‎Rectangular
Size	‎60 Watt
Special Features	‎Detachable AC Cord
Style	‎12 Volt
Type of Bulb	‎LED
Usage	‎ETL Listed for dry and damp location use
Voltage	‎12 Volts
Warranty Description	‎Limited 3-year warranty. This product is for dry and damp locations.
Wattage	‎60 watts

5 Star

4 Star

3 Star

2 Star

1 Star

Donnez votre avis

Votre courriel ne sera pas publié. Tous les champs obligatoires sont marqués d'un^*

Votre note

Scritto da: Thomas H.

Had to replace a unit in the kitchen, and this works perfectly

My under cabinet lights stopped working. Changed the dimmer switches, but it finally was the transformer. All good now.

Scritto da: PVM

Does what it's supposed to

Easy installation. I wired directly to a dimmer switch and it works perfectly.

Scritto da: S.C. Fluhr

Smooth dimming led driver

Quality made, nice and compact, works as advertised

Scritto da: paul

Electrician approved

One of the few LED drivers that can be dimmed in compliance with the NEC for electrical inspection. The cord that came with it can be unscrewed and the driver can be hardwired with 14-2 romex. The connections are circuit board terminal blocks on each end, so they required a jeweler screwdriver. Be sure to hold the blocks when tightening the screws, so the block doesn't torque off the circuit board. The unit does soft start and ramp to full in 1 sec. Other than that, there isn't a 3 sec delay to warm up like cheap switching power supplies have before they instantly pop on at full brightness. That's nice. I had no problem using a z-wave smart dimmer. I used the a Linear aka Nortek aka GoControl model WD500Z5 zwave dimmer and it successfully burned in so far for 1 day. It does get very warm, even pushing only 10 watts. Like a hot McDs coffee cup hot. Not too hot to start papers on fire, but too warm to be comfortable holding. Plan for that when mounting. Also, If you wired several LED homeruns instead of daisy chaining the runs, be sure to plan on wirenuts or a terminal block to connect to the driver- it only has internal room for 1 #12 pair of wires. You have no internal room for other connections. I powered 10 watts of LED under cabinet LED tape. The cables in the pic are 14-2 romex and 16-2 cl2 riser cable. No issues with those gauges.

Scritto da: Snap, Crackle and Pop

A high-quality dimmable, "universal" 120V to 12V DC LED driver power supply

The Armacost Lighting 840600 is a high quality, dimmable power supply for 12V LED fixtures or systems. COMPATIBILITY: This power supply should be compatible with a wide range of 120V dimmers. The installation instructions state the following: "Armacost Dimming LED Drivers are compatible with both forward phase (leading edge, triac, incandescent) and reverse phase (electronic low-voltage, ELV, and trailing edge) AC dimmers ... They are also compatible with low-voltage PWM dimmers and RGB color controllers. "Although virtually all dimmers will work with Armacost Dimmable LED Drivers, Armacost Lighting recommends dimmers that can be programmed or have an adjustment dial to set the low end dimming range." BUILT IN CONNECTORS: The built in connectors work well and quickly. They need to have some of the outer insulation to clamp onto, to keep the stress of any pull on the wire from going to the terminal connection itself. So don't strip too much of the inner or outer insulation. LOW MINIMUM POWER LOAD: The minimum power load is just 5 watts. VOLTAGE: Output is 12V DC. DIMENSIONS: It's somewhat large, at 7-1/16 inches long by 2-3/8 inches wide by 1-3/8 inches high. ENCLOSURES: If you want an enclosure, Armacost makes variations with enclosures for conduit connections. The only real negative is the cost, though of course having a high-performing, high quality power supply makes it a reasonable value. Lower-watt drivers are less expensive than this one. The manufacturer's website has lots more info, including specs and installation instruction. TWO WARNINGS: First, be sure to get a power supply rated with enough watts to cover your needs. Second, be careful to get a power supply with the right input voltage. Armacost makes a line of 12V dimmers and matching power supplies. This product is the universal power supply, to be used with a range of dimmers and 120V.

Scritto da: CAMPFIRESKY

NEW KITCHEN SINK LIGHTING

Very easy to install. I hard wired the power pack and also installed a dimmer switch. Works perfectly with no humming. Great product.

Scritto da: Kindle Customer

Everything I wanted at a reasonable price

Put in a dimmer switch and get the 120 leds per meter. You can crank it up to give all the light you will ever need and yet dim it down to simply add ambience to your kitchen. I installed them in the channel with the diffusers and absolutely love them.

Scritto da: Nick

It actually works with a dimmer!!

Wow an LED driver / power supply that actually dims the LEDs!!! I thought there was something wrong with my LEDs or dimmer as I tried two different PLUSPOE dimmers that did not actually dim anything and also buzzed. This driver actually works, and works well. I am using the 12v/24watt one to drive 8x half moon 12v LED stair lights. I am also using a Leviton 6674 dimmer in the wall. There is no switching noise from this driver, the construction is solid and the dimming is smooth without flicker. Completely worth the higher price than non certified drivers. The only thing that was odd is that it did not come with a power cord. The lack of a power cord was not a big deal as I had one laying around, but I could see it bothering other people. I have a light switch controlling half of a receptacle in low voltage box, so I did need one.