CURT 55537 Faisceau de câblage de remorque 4 broches côté véhicule, compatible avec certaines Dodge Caravan, Grand, Chrysler Town and Country

Brand:CURT

3.6/5

69.25

Si votre véhicule n'est pas équipé de câblage pour tracter une remorque, le câblage sur mesure CURT est la solution idéale. Un faisceau de câbles personnalisé - également appelé connecteur en T - est un appareil électrique simple et prêt à l'emploi qui se branche sur votre système électrique automobile et fournit une connexion de câblage de remorque standard et universelle. Cela se fait à l'aide de deux ou plusieurs connecteurs compatibles OEM spécifiques au véhicule à brancher sur l'ensemble de feu arrière, éliminant ainsi le besoin de couper, d'épisser et de souder pendant l'installation. Les faisceaux de câbles personnalisés sont spécifiques au véhicule et, bien qu'ils ne soient pas disponibles pour tous les véhicules, ils offrent l'un des moyens les plus rapides, les plus simples et les plus sûrs de câbler un véhicule pour le remorquage. Ce faisceau enfichable particulier fournit une prise de connecteur plat à 4 voies et est conçu pour être un faisceau de câblage personnalisé pour s'adapter à certaines années de la Dodge Caravan, Dodge Grand Caravan et Chrysler Town and Country (pour vérifier la compatibilité de votre véhicule, voir les informations d'application ). Il est livré avec tous les composants de câblage nécessaires pour établir une connexion de câblage de remorque fiable, ainsi qu'un cache anti-poussière pour garder le connecteur propre lorsqu'il n'est pas utilisé. Vous avez une image en tête de votre prochaine destination - peut-être est-ce le débarquement du bateau sur votre lieu de pêche préféré, peut-être est-ce un camping qui surplombe l'un des chefs-d'œuvre de la nature, ou peut-être est-ce le prochain grand chantier. Cependant, transformer cette image en réalité demande plus qu'une simple rêverie. Il faut une connexion solide et la bonne quantité de puissance. Le câblage personnalisé CURT est fabriqué avec certaines des technologies les plus sophistiquées de l'industrie et est conçu pour être installé facilement, vous offrant une connexion électrique durable pour votre configuration d'attelage de remorquage.

HOUSSE DE PROTECTION. Pour favoriser une utilisation durable et une résistance aux intempéries, ce faisceau de câbles d'éclairage de remorque à 4 pôles est livré avec un cache anti-poussière en caoutchouc. Il s'adapte facilement sur le connecteur plat 4 voies lorsqu'il n'est pas utilisé, le protégeant ainsi des éléments extérieurs. PRISE EN MAIN FACILE. Brancher le câblage de votre remorque et les feux de votre remorque est facile grâce à la conception ergonomique de cette prise de véhicule. Il comporte des languettes en haut et en bas pour une meilleure prise en main lors du branchement ou du débranchement de votre remorque. SPÉCIFIQUE AU VÉHICULE. Ce faisceau de câblage de remorque de véhicule de rechange est conçu pour certaines années de Dodge Caravan, Dodge Grand Caravan et Chrysler Town and Country. CONNECTEUR STANDARD. Ce câblage de remorque enfichable à 4 plats peut être utilisé pour connecter les feux arrière de la remorque, les feux de freinage et les clignotants. Le câblage d'éclairage de remorque à 4 voies est populaire sur une variété de remorques, ajoutant des options de remorquage polyvalentes pour votre véhicule. FACILE À INSTALLER. Pas de découpe ! Pas d'épissure ! Ce kit de faisceau de câbles de remorque se branche sur le câblage d'usine existant de votre véhicule et l'équipe d'un connecteur de câblage de remorque arrière standard à 4 broches pour brancher et tracter une remorque.
Brand CURT
Brand ‎CURT
Country of Origin ‎USA
Customer Reviews 4.6 4.6 out of 5 stars 196 ratings 4.6 out of 5 stars
Exterior ‎Smooth
Is Discontinued By Manufacturer ‎No
Item Dimensions LxWxH 9 x 4 x 3 inches
Item model number ‎55537
Item Weight 0.31 Pounds
Item Weight ‎5 ounces
Manufacturer ‎Curt Manufacturing
Manufacturer Part Number ‎55537
Material Rubber
Model ‎Custom Wiring
OEM Part Number ‎55537
Product Dimensions ‎9 x 4 x 3 inches

3.6

13 Review
5 Star
74
4 Star
17
3 Star
3
2 Star
1
1 Star
4

Donnez votre avis

Votre courriel ne sera pas publié. Tous les champs obligatoires sont marqués d'un*

Scritto da: Keith
Quick and easy
This was very easy to install, less than 20 minutes. Works great.
Scritto da: Tricker
Towing with lights is good
Read instructions, installed, lights up my trailer. Saved a bunch of money diy baby!
Scritto da: Alicia Mick
Ok
I wish there was a way to route it a diffrent way but had to come out the back when I use it because of the stow n go but it works fine just tuck it back in the trunk when not using
Scritto da: D. WALTER
Took a little maneuvering to install
When I bought this trailer light wiring harness for my 2005 Chrysler Town and Country, I thought it would be the same as with my 2005 Dodge Durango, and go on in a couple of minutes, but I was severely wrong. With this wiring harness, you have to push the ends of the wiring harness through a couple of prefab holes in your auto body. The problem with this is that there is insulation between the interior and exterior body panels, and the holes you need to push the wiring harness through can get pretty tight. The left side tail light was fairly easy with a larger hole in the body panel, I was able to put my hand in farther, and push the wiring harness easier. The Right side taillight was a little harder because the body panel hole on the interior was smaller, and a little lower than the exterior hole, so much more difficult to maneuver through the body. We ended up cutting the end of the right side wiring harness off, and running the wire through the panel, and then reattaching the harness end to the wire once it was through the body. Also, something I wasn't aware of with this harness is that the 4 pin connector is not maintained on the outside of the vehicle. This wiring harness stays inside the vehicle until you are ready to use it, and then you run the wires out through the back door whenever you're going to use it. The part I don't like about this harness is shutting the door on the wires. I know that there is weather stripping there, and it probably won't cut the wires by being closed on them, but I just feel it might degrade the life of the harness... Otherwise, so far so good. Decent wiring harness, somewhat difficult installation, but still functional, and decent quality.
Scritto da: Nicholas Maddox
Easy to install
Easiest install for any wiring project I’ve ever done!
Scritto da: John F
Quick use!!
Took about 5mins to install. I did not run it back through the body. I just ran the wires under the light assembly. Then pushed the wires inside the van 5mins tops. Didn't care for the ground wire. Had to use a drill Tel screw to the body. They could've tied that into the other white wires since the body harness for the lights is already grounded. Other than that no problems.
Scritto da: Keith J Rigden
Get it
Pretty easy to install in my 06 Grand Caravan. Routing to the passenger side requires you to fish it to the light cavity. Get a good look at what's going on there before you tie on. Wish the set was longer. Watched one video, but it was for another brand. This product is too short to route it their way, which is a little cleaner, but not a big deal. Only reason for knocking a star off. Worth every extra penny to not have splice anything!!
Scritto da: Ashish Desai
Very easy to install and worked with no issues
The harness is super easy to install on a 2005 dodge grand caravan sxt stow and go. Took about 20 minutes with no prior experience of knowing anything dodge or harness wiring. The self tapping ground screw worked instantly under the gamble and the length of excess wire is about 15 inches which is plenty to reach my trailer. Literally you can do this by watching a YouTube video on your phone and doing it same time. Definitely buy this kit and do not pay to get it installed ..you can do It yourself
Scritto da: Kevin from Calgary
Works well for my little trailer with LED lights.
Works well with my little trailer. Note that this kit does not contain a powered converter, so your trailer lights are powered from the vehicle's tail light wiring. If your small trailer has LED lights, this setup is fine. On my 2005 Grand Caravan, this kit will allow the trailer connector to extend outside the tailgate by a foot, or perhaps a little more. It takes a fair bit of cutting in the existing tail light wiring grommets for the hole to be large enough to push the connectors through to the space behind the taillights. That small tube of black silicon sealant is to reseal the grommet where you cut through. I used coil-style plastic wire loom to protect the wiring as it exits under the tailgate.
Scritto da: JP
Price was right, easy to install
Great price point, installed on an 04 caravan, took about an hr but never installed a trailer harness before. Good product!
Scritto da: Mr.Kent
works great.
no problems, works great.
Scritto da: Amazon Customer
... cable cannot be stored in the tire jack compartment like the other brand
It works with the exception that the plug is very tight and the cable cannot be stored in the tire jack compartment like the other brand. Minor problems. Seems to work OK.
Scritto da: Dompti
????
Parfait mais je l’es retourner je n’avais plus besoin.

Produits connexes

Découvrez notre réseau international

Nous expédions dans 28 pays plus de 200 000 produits. Restez informé, inscrivez-vous à la newsletter.

Array