CURT 55542 Faisceau de câblage de remorque à 4 broches côté véhicule, compatible avec certaines Toyota Corolla Sedan, noir

Brand:CURT

3.8/5

86.62

Si votre véhicule n'est pas équipé de câblage pour tracter une remorque, le câblage sur mesure CURT est la solution idéale. Un faisceau de câbles personnalisé - également appelé connecteur en T - est un appareil électrique simple et prêt à l'emploi qui se branche sur votre système électrique automobile et fournit une connexion de câblage de remorque standard et universelle. Cela se fait à l'aide de deux ou plusieurs connecteurs compatibles OEM spécifiques au véhicule à brancher sur l'ensemble de feu arrière, éliminant ainsi le besoin de couper, d'épisser et de souder pendant l'installation. Les faisceaux de câbles personnalisés sont spécifiques au véhicule et, bien qu'ils ne soient pas disponibles pour tous les véhicules, ils offrent l'un des moyens les plus rapides, les plus simples et les plus sûrs de câbler un véhicule pour le remorquage. Ce faisceau enfichable particulier fournit une prise de connecteur plat à 4 voies et est conçu pour être un faisceau de câblage personnalisé pour s'adapter à certaines années de la berline Toyota Corolla (pour vérifier la compatibilité de votre véhicule, voir les informations d'application). Il est livré avec tous les composants de câblage nécessaires pour établir une connexion de câblage de remorque fiable, ainsi qu'un cache anti-poussière pour garder le connecteur propre lorsqu'il n'est pas utilisé. Vous avez une image en tête de votre prochaine destination - peut-être est-ce le débarquement du bateau sur votre lieu de pêche préféré, peut-être est-ce un camping qui surplombe l'un des chefs-d'œuvre de la nature, ou peut-être est-ce le prochain grand chantier. Cependant, transformer cette image en réalité demande plus qu'une simple rêverie. Il faut une connexion solide et la bonne quantité de puissance. Le câblage personnalisé CURT est fabriqué avec certaines des technologies les plus sophistiquées de l'industrie et est conçu pour être installé facilement, vous offrant une connexion électrique durable pour votre configuration d'attelage de remorquage.

HOUSSE DE PROTECTION. Pour favoriser une utilisation durable et une résistance aux intempéries, ce faisceau de câbles d'éclairage de remorque à 4 pôles est livré avec un cache anti-poussière en caoutchouc. Il s'adapte facilement sur le connecteur plat 4 voies lorsqu'il n'est pas utilisé, le protégeant ainsi des éléments extérieurs. PUISSANCE FIABLE. Ce faisceau de câblage de remorque à 4 voies est construit avec la technologie de montage en surface. Ce type de circuit génère moins de chaleur, une intensité lumineuse optimale et des performances durables. SPÉCIFIQUE AU VÉHICULE. Ce faisceau de câblage de remorque de véhicule de rechange est conçu pour certaines années de la berline Toyota Corolla. CONNECTEUR STANDARD. Ce câblage de remorque enfichable à 4 plats peut être utilisé pour connecter les feux arrière de la remorque, les feux de freinage et les clignotants. Le câblage d'éclairage de remorque à 4 voies est populaire sur une variété de remorques, ajoutant des options de remorquage polyvalentes pour votre véhicule. FACILE À INSTALLER. Pas de découpe ! Pas d'épissure ! Ce kit de faisceau de câbles de remorque se branche sur le câblage d'usine existant de votre véhicule et l'équipe d'un connecteur de câblage de remorque arrière standard à 4 broches pour brancher et tracter une remorque.
Brand CURT
Brand ‎CURT
Country of Origin ‎USA
Customer Reviews 4.7 4.7 out of 5 stars 348 ratings 4.7 out of 5 stars
Is Discontinued By Manufacturer ‎No
Item Dimensions LxWxH 9 x 4 x 3 inches
Item model number ‎55542
Item Weight 0.79 Pounds
Item Weight ‎12.6 ounces
Manufacturer ‎Curt Manufacturing
Manufacturer Part Number ‎55542
Material Rubber
Model ‎Custom Wiring
OEM Part Number ‎55542
Product Dimensions ‎9 x 4 x 3 inches

3.8

13 Review
5 Star
83
4 Star
11
3 Star
2
2 Star
1
1 Star
3

Donnez votre avis

Votre courriel ne sera pas publié. Tous les champs obligatoires sont marqués d'un*

Scritto da: Antonio rogano
Easy install
Steal deal, worth every penny.
Scritto da: db_review
Easy towing with a Corolla
The CURT T-Connector was fairly easy to install - very much easier than having to splice in an old-fashioned kit. One problem is that the included instructions are "brief" to put it mildly - they don't cover all of the steps and skip a lot of details. I subtract half a star for this. I found a useful installation video from another vendor's web site though, and that was quite nice. The other problem is that the wiring coming out of the circuit breaker is routed out the left and right sides, making it difficult to find a good spot to adhere the circuit breaker to the car - wires get bent for no reason because no matter how you route them, one side is always going the wrong way. If the wires were routed the TOP and your RIGHT (as you look down at the face of it), then there is a great spot for it against the rail in the cavity behind the trunk lining and no wires get bent. I subtract another half star for this. I have some pointers to share from my installation experience: Use the proper tool for removing the paneling:TEKTON 5873 Door Panel Remover . Otherwise you are prying at the plastic fasteners with a screwdriver and it takes longer and bends the fasteners. Save them, because you have to reinstall them. I did not buy the tool, and it took longer. Don't mount the circuit breaker to the trunk until all of the wires are connected and the cords routed the way you want them, or you might have to pry off the adhesive and do it again, like me. Since the adhesive only works once, I used Velcro tape the second time. Use a screwdriver to help depress the plastic tab for removing the tail light connectors. On the left side of my Corolla, I couldn't even see the tab. I could feel it, but couldn't wedge my fingers in that direction. I pressed the tab with a screwdriver and it came out when I pulled. I didn't need this for the other connector. I used a lot more plastic zip ties than were supplied by the manufacturer. Wires go wherever they want to if you're not careful - and I wanted to make sure they stayed out of the way. I tied them to the existing wiring, especially the first few inches from the connectors, where CURT's T-wires seem to want to bulge. I reinforced the wiring with a 1 inch width of duct tape in several key spots (such as where the wires come out of the circuit breaker and where the splices and heat-shrink tubing are). I just wanted to provide some extra strain relief. I decided to route the 4-flat trailer connector wire through the plastic rear-threshold panel, using a hole that exists for the metal tie-down in my trunk. It seemed less awkward than routing under the threshold. I really wanted to cut a 2 inch round hole and store the wire behind the threshold, but my wife didn't want me to :) Finally, don't forget the dust cover - slide it over the 4-flat connector. You can stow the wire under the floor board with the spare tire. This is an easy install for the hands-on individual. It will save $50 installation plus whatever markup another company may charge when you buy it.
Scritto da: Ricky Martin
So easy
One of the very few things that's actually plug-n-play. Just had to remove a little trim in the trunk and plug it into the taillights.
Scritto da: Kacy
No issues.
Easy to install and worked with the trailer.
Scritto da: Amazon Customer
Easy to install! Slight confusion with the installation instructions...
Assembly was just as easy as everybody says it is. The only reason I give it four stars instead of five is that the directions mention attaching the white ground wire to the car. The kit did not come with a white ground wire, and the only white wire that came with it was part of the harness itself. The car already had a white ground wire attached to the frame near the truck latch. After watching some videos online on the installation of this exact product that made no mention of the white ground wire, I deduced that, like a lot of automotive instructions, the white ground wire part of the instructions was either incorrect or out of date. I will amend my review once I have the opportunity to use the wiring harness with a trailer, but so for everything works great. And like I said, with the exception of the white ground wire part, the installation was pretty easy and straightforward.
Scritto da: Charlie
Awesome wire set
Doesn't get any easier than this
Scritto da: Justin O.
Great product great price
Overall this harness worked great and I use it few times a month for a very small trailer vs driving the truck to save fuel. I do wish the instructions had better info though. You can easily swap sides on accident with the connectors vs if the included instructions said brown on this side and the other color on that etc. I looked it on on my phone easily enough but another single sentence would have just helped. Seems to be holding up and plenty of length for various types of trailers and accessories.
Scritto da: Mort
Quick and Easy!
Installation was quick and super simple! I done it in less than 15 minutes with no special tools required (I used flat head screwdriver to pop out the plastic fasteners). **The best part is no need for battery wiring!
Scritto da: Doug W.
Lights on Trailer Works
Quick connect for a trailer to existing Toyota Corolla connectors. You unplug the factory plugs to plug into the Curt connector and then plug the Curt connector to the lights. Light a Y hook-up without any cutting and splicing. I hooked the right block to the left side so initially I had the lights on the trailer reversed. Curt could actually put labels on the electrical blocks to prevent the mix-up when installing. Installation was easy except you have to pull some trunk covers off to hide the wires (I did this twice because of the connector mix-up).
Scritto da: Robert Martin
Worked perfectly.
No fuss installation. Very easy to install. Would highly recommend this part.
Scritto da: Eric Patenaude
Tres bien
Tres facil d installation et fonctionne tres bien sans rien couper. Je recommende
Scritto da: Maxime
quick and easy to install !
the converter is of very good quality and is easy to install. I recommend this product.
Scritto da: patrick97
pour Corolla 2009 wow
bonne qualité de fil les connecteur en plastique aussi epai que ceux de mon auto donc devrai etre fiable et ce kit es tellement ridicule a installer ca fit direct aucun gossage cest plus long defaire la finition de la valise dans l'auto que de brancher ce module et le tape double face parfait la petite boite noir es pas lousse dans le fond es fix coller bien apprecier ce kit rapide et simple a installer

Produits connexes

Découvrez notre réseau international

Nous expédions dans 28 pays plus de 200 000 produits. Restez informé, inscrivez-vous à la newsletter.

Array