MG Chemicals 9410 Adhésif électriquement conducteur en 1 partie avec un temps de travail illimité jusqu'à ce qu'il soit durci à la chaleur. TG élevé, distributeur de 3 ml nouvelle formule

Brand:MG Chemicals

2.1/5

88.45

9410 est un adhésif époxy monocomposant chargé d'argent et conducteur d'électricité. Il est lisse, thixotrope, ne s'affaisse pas et adhère bien à une grande variété de substances. Il a une durée de vie illimitée à température ambiante. Attention! ce produit doit être thermodurci. Ce produit peut créer des liaisons électriquement conductrices là où la soudure n'est pas une option, comme lors de la liaison à des composants sensibles à la chaleur, du verre, des métaux mous ou des polymères conducteurs. Il fonctionne également bien dans les emballages de semi-conducteurs, les fixations microélectroniques et le scellement des couvercles, et comme fixation de matrice pour les petites puces, les LED et les diodes. Il ne nécessite pas de mélange et peut être facilement utilisé dans les processus de distribution manuels, pneumatiques et robotisés. 9410 a été formulé pour avoir un TG élevé. Pour un TG inférieur, utilisez 9400.

Conductivité thermique de 1,1 W/(m·K). Tg de 96 °C [204,8 °F]. Durée de conservation : jusqu'à 4 mois à 25 °C. Congelé = 1 an. Thermopolymérisation uniquement. Température de durcissement minimale de 90 °C [194 °F]. Résistivité de 1,8 x 10-3 Ω·cm.
Brand MG Chemicals
Color Silver Grey
Compatible Material Glass
Country of Origin Canada
Item Form Chips
Item model number 9410-3ML
Manufacturer MG Chemicals
Material Silver, Epoxy
Product Dimensions 1.01 x 8.06 x 1.01 inches; 0.33 Ounces

2.1

10 Review
5 Star
39
4 Star
5
3 Star
14
2 Star
4
1 Star
39

Donnez votre avis

Votre courriel ne sera pas publié. Tous les champs obligatoires sont marqués d'un*

Scritto da: Fred E. Elum
No Instructions Included
I bought this for a project that I was unsure if I could heat. I did not want to use my low temp solder. When it arrived there is paper in the packaging, but no instructions. I found the TDS on the manufacturer website. It must be heated to activate the epoxy. Higher temperature give shorter cure time. If this information were in the description I would not have purchased. Curing is between 90C-120C for 60-7 minutes. My low temp solder activates at about 125C, so it is little benefit. It does not have any adhesion until cured. It did not run , but it did not hold the pieces together until I could heat it. It has a very distinct formaldehyde odor when curing. Don't breathe the vapors. UPDATE Jun 2021: It seems to work as intended. Additionally, the seller seems to have updated the listing and information to include that it must be heat cured. That information was not present when I bought it. At over ten bucks a gram instructions should be provided....
Scritto da: Scott
HEAT Cured Only!
The title for this product should be much more explicit - this adhesive requires a minimum of 70 degrees C/158 degrees F to cure.
Scritto da: Dawn
Dried up
For the money spent on a small market product that you can not find readily you would expect it to show up in working order. It was USELESS as it had gone bad probably years ago and was sitting on a shelf till the next poor sap ordered it. Please read all the reviews and do not buy this trash. Now I have to ship it back to get my money refunded. What a huge waste of time.
Scritto da: Ray
EPoxy
Make sure you wear protective gloves.
Scritto da: Guillermo Hernandez
Does not work at all
I applied 80C temperature for 30 minutes and it does not dry and will not bond at all. It is not like shown in the video, it is like a paste that is difficult to apply. I have tried this product three times and it is the same results. Another Chinese useless product?
Scritto da: Behnam
Great dispensing quality
This product is very easy to dispense and use. No mixing is required and it is very conductive too.
Scritto da: Adrian T.
Arrived fully cured and unusable
The shelf life of this product is not unlimited and it had clearly expired or been stored in an environment that was too warm. It was fully cured and unusable. It did not ship with any certs or expiration date documentation so who knows how old it was. I bought the two-part system to replace it because the shelf life is much longer than the one-part
Scritto da: Amazon Customer
Awesome stuff!
Works awesome, used to bond aluminum wires to copper pad. Worked perfectly.
Scritto da: Rick Barnier
No good
Went to use the product for the first time and it was all dried up on the inside. Lost a customer due to this.
Scritto da: thomas
dans l os
texture pas fluide et pas moyen de la faire catalysé malgré 2h a 80°

Produits connexes

hot
Résine époxy West System 105-B
3.7/5

€ 177.77

Résine époxy West System 105-B
3.7/5

€ 177.77

Découvrez notre réseau international

Nous expédions dans 28 pays plus de 200 000 produits. Restez informé, inscrivez-vous à la newsletter.

Array