Pince à sertir assistée par impact Malco C5A2

Brand:Malco

3.4/5

€
211.84

L'impact de sertissage turbo Malco est un accessoire simple et compact qui fonctionne exclusivement avec l'assistance électrique de la technologie Impact Driver pour sertir efficacement et en toute sécurité des conduits ronds galvanisés de calibre 30 à 24 (0,41 à 0,71 mm) et (0,31 à 0,61 mm) noirs. tuyau de poêle. L'impact de la sertisseuse turbo ne nécessite ni configuration ni réglage. Il suffit de fixer l'arbre d'entraînement de rainure de puissance de 1/4" à votre visseuse à chocs sans fil ou filaire (min. 12 volts CC / max. 7 A CA) pour commencer immédiatement à sertir plusieurs tailles, types et épaisseurs de tuyaux et de conduits, y compris le conduit en spirale, rapide et facile. Avec la couture du tuyau ou du conduit en position fermée, commencez le sertissage sur un côté de la couture en tirant doucement sur la gâchette du pilote et en inclinant l'impact de la sertisseuse turbo sur le bord métallique. Déplacez la pince à sertir autour de la circonférence du tuyau de manière contrôlée, puis inclinez la pince à sertir hors du métal lorsque la pince à sertir s'approche de l'autre côté du joint. L'impact de la sertisseuse turbo est cinq fois plus rapide qu'un outil de sertissage manuel basé sur des essais réels sur le terrain ! il est confortable pour tout opérateur de manœuvrer et, les gauchers en prennent note, il fonctionne avec le conducteur d'impact en marche avant ou en marche arrière. Le petit impact de sertissage turbo pratique est un accessoire indispensable pour chaque installateur de CVC et se range facilement dans une pochette ou un sac à outils prêt lorsqu'il n'est pas utilisé.

Montant

Ajouter au panier Acheter maintenant

EAN: 0686046547091

Catégories Outils et amélioration de la maison, Sets de batteries et chargeurs, Outils à main, Sertisseuses de fils,

Se range dans une pochette ou un sac. Compact, facile à manœuvrer et à équilibrer. Pas de configuration ni de réglage. Sertissages 30-24 ga. (0,41-0,71 mm) conduit métallique rond. Transforme rapidement votre tournevis à percussion en pince à sertir.

Batteries Included?	‎No
Batteries Required?	‎No
Brand	Malco
Brand	‎Malco
Color	Black
Color	‎Black
Country of Origin	‎USA
Customer Reviews	4.4 4.4 out of 5 stars 662 ratings 4.4 out of 5 stars
Grip Type	‎Ergonomic
Handle Material	Metal
Handle Material	‎Metal
Is Discontinued By Manufacturer	‎No
Item Dimensions LxWxH	8.25 x 6 x 2 inches
Item Dimensions LxWxH	‎8.25 x 6 x 2 inches
Item model number	‎C5A2
Item Package Quantity	‎1
Item Weight	2.1 Pounds
Item Weight	‎2.1 Pounds
Manufacturer	‎Malco Products
Material	‎steel
Measurement System	‎Metric
Part Number	‎C5A2
Power Source	‎Hand Powered
Product Dimensions	‎8.25 x 6 x 2 inches
Style	‎Crimper
Warranty Description	‎Limited

5 Star

4 Star

3 Star

2 Star

1 Star

Donnez votre avis

Votre courriel ne sera pas publié. Tous les champs obligatoires sont marqués d'un^*

Votre note

Scritto da: Anthony

Absolute wrist saver

I’ve done hvac for over 4 years now hand crimping spiral and snap lock sheet metal and once I bought this my efficiency shot through the roof. Great crimps every single time super easy to use, durable, and easy on your impact great purchase

Scritto da: Kristina Kreitzer

Better than hand crimpers

I’m a union sheet metal worker, and this thing is awesome. A bit of a learning curve l, but once you get the hang of it there’s no turning back. This thing has some weight to it which surprised me at first, but after using it I understand why. I’ve been looking at buying this for about a year, finally pulled the trigger and I’m glad I did. 5 secs is all it takes to crimp a pipe and it’s a close to a factory edge. I stop before the seam afraid to blast through it, though I’m sure it will handle it. Im very happy have to wait to see how long the shank lasts.

Scritto da: Ed

On the pricey side but faster than hand crimping

I was skeptical about buying this because it's not cheap. Hand crimpers are a lot cheaper. But I'm very impressed at how it crimps. It's noisy and you can only use it with a impact. I tried using it with my regular drill and it twisted the pipe and cut my arm so do not use anything but an impact it even has a warning label. But if you're crimping lots of pipe there's no competing with a hand crimper at how fast you can use this. Definitely worth the money if you are made of it.

Scritto da: Scott Messina

Saves your forearms

This is much faster than hand crimping, and far easier on your hands and forearms. I can crimp a 10" duct in about 10 seconds, while it's already mounted. Because this goes on the end of your impact, it can spin 360 to modify duct that's already in the air, as long as you've got 2+ inches all of the way around. Just don't go over a seam, it says so right in the instructions. It takes a few tries to learn the best way to get it fully engaged on the pipe, I just go forward a couple of clicks, then reverse back to the starting point, and it's ready to go. I am using it with a Milwaukee M12 Surge impact, so it's noise level isn't too bad. With a standard impact, it will likely be quite loud, especially when amplified by uninsulated ducting

Scritto da: Jason

Must have? Or nice to have? That’s the question.

It’s quit useful and saves tons of time if your cutting a lot of duct. There is one issue I have come across. I found that using this with fittings, like els, I found the crimp isn’t enough. I need to hand crimp a bit because it’s not quite enough to fit the duct to the fitting. Still worth it and a valuable tool. Is it a must have? I wouldn’t say that. But I’m very happy with it and do recommend it.

Scritto da: Placeholder

Great product

Thus is so fast and saves so much time when installing metal ducting, it’s a great tool

Scritto da: James

Worth it!

If you do much work with round sheet metal ducting this is worth it, in one job I used it so many times I didn’t even think I would need it and it saved so much time, it’s far quicker and results in more professional look than a hand crimper. It takes a little getting used to though but after that it’s awesome

Scritto da: Duct Sealant Joe

Fantastic, but....

Month in and is already wearing out a little bit. Works maybe a little too well. Will over crimp things by a half inch for circular duct. Otherwise it saves my time, and my hands. Would recommend

Scritto da: Tyler little

Beware! Can become a 270$ tool quickly

This thing is awesome! It crimps spiral better than you get from the shop, that being said if you push it too hard or try to crimp over a seam the drive shaft will snap. Malco has you covered though for almost 70$ they will send you a replacement shaft which is little more than a nut driver (10mm I think) with a shoulder at the end to hold it to the tool. If this easily replaceable, and easily broken part was a reasonable price this thing would get 5 stars all day. If you have a friend with a metal lathe maybe you can whittle up a cheaper replacement.

Scritto da: Jeff Arbeau

Forget what you know about crimping! 2ND REVIEW

The media could not be loaded. You have to learn how to use this tool. This crimper is nothing like any way you crimped before. Go low and slow till you ght the fell of it. Wish I had this 20 years ago. I love it!!

Scritto da: Brendon Maclellan

Awesome

This thing save so much time and energy. Love it. Highly recommended

Scritto da: Amazon Customer

Crap

Its crap. It rips apart ductwork and when you are super careful and actually get it to crimp all the way around it doesn't even crimp it enough for it to fit.