Steelex M1082 Ensemble de porte-clés Woodruff 9 pièces

Brand:Steelex

3.3/5

€
112.97

Du fabricant Cet ensemble de tiges HSS 1/2" avec plateau en bois comprend : 3/16" par 1", 1/4" par 3/4", 3/16" par 3/4" , 1/8" par 3/4", 5/32" par 5/8", 3/32" par 5/8", 1/16" par 1/2", 1 /8-Inch par 1/2-Inch et 1/8-Inch par 3/8-Inch cutters.

Aucune unité disponible

EAN: 0754001510821

Catégories Outils et amélioration de la maison,

Hss, tige 1/2". 1/16" par 1/2", 1/8" par 1/2", 1/8" par 3/8". 5/32" par 5/8", 3/32" par 5/8". 3/16" par 3/4", 1/8" par 3/4". 3/16" par 1", 1/4" par 3/4".

Batteries Included?	‎No
Batteries Required?	‎No
Country of Origin	‎India
Customer Reviews	4.3 4.3 out of 5 stars 46 ratings 4.3 out of 5 stars
Domestic Shipping	Item can be shipped within U.S.
International Shipping	This item can be shipped to select countries outside of the U.S. Learn More
Is Discontinued By Manufacturer	‎No
Item model number	‎M1082
Item Package Quantity	‎1
Item Weight	‎15.2 ounces
Manufacturer	‎Steelex
Material	‎HSS
Measurement System	‎Imperial
Package Dimensions	‎5.6 x 2.8 x 2.6 inches
Part Number	‎M1082
Warranty Description	‎1-Year Warranty

5 Star

4 Star

3 Star

2 Star

1 Star

Donnez votre avis

Votre courriel ne sera pas publié. Tous les champs obligatoires sont marqués d'un^*

Votre note

Scritto da: Bruce Wilson

Great deal

Great product!

Scritto da: Cletus Berkeley

Good Cutters

Recently got these for my shop-floor. Good set of cutters at a reasonable price. Use lots of oil when cutting and go slow with feeds and speeds. Some info per ANSI B17.2 follows: DEPTH CUT KEY ID NOMINAL SIZE +0.005 -0.000 403 1/8 x 3/8” 0.1045” 204 1/16 x 1/2” 0.1668” 404 1/8 x 1/2” 0.1355” 305 3/32 x 5/8” 0.1981” 505 5/32 x 5/8” 0.1669” 406 1/8 x 3/4” 0.2455” 606 3/16 x 3/4” 0.2143” 806 1/4 x 3/4” 0.1830” 608 3/16 x 1” 0.3393”

Scritto da: sfoote

Good Enough

These cut very well, for the price. Was able to cut a 1/8"x1/2" key seat into the shank of a 3/4" grade 8 Hex Bolt with zero issues. Very clean cut. If you watch your feeds & speeds and use a quality cutting oil, these should hold up for small scale general machine work. Only 4 stars because these cutters do not have the inch-size listed on the wooden holder OR on the shank of the cutter.

Scritto da: Nick

So-so

Haven't played with them much yet, but cutting a short groove in mild steel produced noticeable wear on the cutter. I did do it dry with one of the cutters I'm less likely to use in case it suffered, so I'll try with lubrication next time and see what happens. I'm sure they'll work fine for aluminum and polymers, but if you're going to be cutting steel, especially hardened steels, buy higher grade cutters.

Scritto da: Cb Finley

Nice

Nice cutter selection

Scritto da: Fella

A lot of cutters for a really great price. Seem to be performing great so far.

The cutters appear to be well made. The two I've used run true and cut an accurate slot. The material I'm cutting is nickel silver, a copper alloy so I can't say how well they would perform on steel. It's still a tricky material to work with and I'm pleasantly surprised with the surface finish on the finished parts. Your getting a lot of cutters for a really low price and I had my doubts about them. Perfect for the job I'm doing and really nice to have in the machine shop for those odd jobs. Not sure they'd be my choice for heavy use large volume work. A good purchase for the machine shop as long as you keep your expectations in check.

Scritto da: Jim Luthje

Works fine!

I've only used 1 of the cutters so far but it did a great job cutting the keyway to the proper size. I'm only giving it 4 stars because I haven't used them all but if they all work as well as the 1 I used it would deserve the fifth star!

Scritto da: Pat

too thick

cut well but .003 to .005 too thick and create loose keyway. Bad quality control