uxcell Fraise affleurante 1/4 x 1/pouce 76 mm 7,6 cm de long 2 bords pour charpentier bleu 2 pièces

Name: uxcell Fraise affleurante 1/4 x 1/pouce 76 mm 7,6 cm de long 2 bords pour charpentier bleu 2 pièces
Brand: Uxcell
SKU: 0702105932346
Price: 38.69 EUR
Availability: InStock

Brand:Uxcell

2.8/5

€
38.69

Caractéristiques : fraise affleurante, double tranchant, tige droite, roulement d'extrémité, utilisé pour couper le contreplaqué, le bois dur, le bois tendre, etc.

Montant

Ajouter au panier Acheter maintenant

EAN: 0702105932346

Catégories Outils et amélioration de la maison, Sets de batteries et chargeurs, Pièces et accessoires pour outils électriques, Pièces et accessoires pour routeurs, Router Bits, Mèches pour traitement des bords et rainurage,

Poids net : 111 g ; Contenu de l'emballage : 2 mèches de garniture affleurantes ; 1 étui en plastique. Couleur bleue; Matière : Acier, Carbure. profondeur de coupe : 30 mm/1,2 ; Longueur totale : 76 mm / 3. Diamètre de la tige : 6,35 mm / 1/4 ; Diamètre de coupe : 6,35 mm / 1/4. Nom du produit : embout de garniture affleurant ; Standard : 1/4 x 1/4 ; Diamètre du roulement : 7 mm.

Brand	Uxcell
Is Discontinued By Manufacturer	No
Item Dimensions LxWxH	2.99 x 0.28 x 0.28 inches
Item model number	a14101300ux0197
Manufacturer	uxcell
Material	High Speed Steel
Product Dimensions	2.99 x 0.28 x 0.28 inches; 2.12 Ounces
Shank Type	Straight
Tool Flute Type	Straight

5 Star

4 Star

3 Star

2 Star

1 Star

Donnez votre avis

Votre courriel ne sera pas publié. Tous les champs obligatoires sont marqués d'un^*

Votre note

Scritto da: Varner House

You get what you pay for -- Set your expectations accordingly.

Based upon the other reviews, I was skeptical. When I received the bits, the first thing I did was inspect the bearings. Neither of them would come off. I tried to unscrew them with an allen wrench, because I was going to put some lock-tite on them, just in case. I was unable to remove the bearings. So I felt pretty safe that they'd stay on. The first bit worked hard for about 90 minutes, then got warm, and I think the thermal shocks from starting / stopping and what-not eventually degraded the steel alloy (and man is it some grainy crap) below the cutter and it snapped. Drat. It is a 1/4" shank and cutter, which means the part below the cutter is way less than 1/4"... I think I just asked more from the tool than it can give. The second bit finished the job and had survived so far. It's only got about 15 minutes of use on it. You get what you pay for, and there's a reason the big quality name-brands don't sell bearing topped flush trim bits in this size. 1/4" shanks and cutters don't exactly have a lot of 'meat' on the bone. For the price, these did the trick, saved me a ton of headache and time with a scroll saw and a sander, and I think it was worth it.

Scritto da: G. D. Dart

After reading some very bad reviews the first thing I did after receiving them ...

Have not had a chance to use them yet. After reading some very bad reviews the first thing I did after receiving them was to take the guide bearing off and oil them both guide bearings came off with no trouble. I saw one review where the bits were not 3" long but the ones I received were I have not figured out how come someone got different lengths. Over all I would say they are not of very high quality, any 1/4 inch shaft router bit is not as good as a 1/2 inch shaft due to vibrations and wear. I believe they will be all right for light duty and not extended use.

Scritto da: Blind woodcrafter

Flush Trimming

This Flush Trim Router Bit works well. It is sharp, cuts smooth and is still holding up after a handful of projects. When the time comes I will purchase another one.

Scritto da: somebody

This is a good buy, I know they come from China

This is a good buy, I know they come from China, but this is one of their better products. the router bits I received were packaged just like the ones in sears, lowes or Home Depot, the blades were attached to the shaft cleanly and not like other bits from china with solder or weld completely visible & always over evident. The blue paint between the cutting surface and shaft was even straight. The cutting surfaces appear to be decent steel (I have only cut wood and can't be certain less I cut something harder). ....yet... I am suspecting these router bits are from a typical name brand product that is being manufactured overseas.... Shipping is a couple days slow across the ocean, but I am recommending these as a good buy.

Scritto da: KJac

Decent product.

Bearing is a little small, enhances channeling on wood work especially softer wood.

Scritto da: James F. Rees

... i needed but it lost it's edge and dulled pretty quickly while flush cutting poplar

The price was right and the bit did what i needed but it lost it's edge and dulled pretty quickly while flush cutting poplar.

Scritto da: Amazon Customer

Works as described

Good tool for the price

Scritto da: JD Texas

Broke on first use

I was excited about getting the bit however, it broke ( the guide wheel) came off/got unscrewed within about 10 minutes of use (cutting countertop laminate). For this reason will not purchase this item again nor will recommend it to anyone. Disappointed! BTW, when I ordered this item it stated it was 2 piece, I only received one. When the one I received broke during 1st use, I ended up going to Home Depo and buying a $20 bit. All in all a true disappointment!