0
0

Ganzen:€ 0.00

Kuckt de WeenchenOfmellen
LoginRegister
0

Ganzen:€ 0.00

Kuckt de WeenchenOfmellen
LoginRegister

2x4basics 90164MI Benotzerdefinéiert Aarbechtsbank a Regallagerungssystem, Schwaarz Aarbechtsbänk mat Regal

Brand:2 x 4 Basics

3.7/5

€
262.75

PRODUITBESCHREIWUNG Den Hopkins 90164 2X4Basics Workbench A Regallagerungssystem bitt en einfache Fix op personaliséiert Regaler. All Hardware ass abegraff, Füügt just d'Gréisst Lumber bäi Dir wëllt (Holz net abegraff). Einfach Assemblée mat nëmmen engem ugedriwwenen Schrauwendréier an enger Séi, Keng Mier oder Wénkelschnëtt noutwendeg. Ideal fir d'Garage a Schapp, d'Regal Links sinn haltbar a robust, déi Iech d'Fäegkeet ginn Är Saachen einfach op Lagerregaler ze organiséieren. Erstellt en Aarbechts- a Späicherplatz dee wierklech op Är Bedierfnesser passt mam 2X4Basics Workbench Assemblée Kit. Dësen innovativen Do-It-Yourself System léisst Iech einfach eng personaliséiert Workbench a manner wéi enger Stonn montéieren. Alles wat Dir braucht ass Sperrholz An 2X4S An Dir hutt eng Aarbechtsbänk déi all Äre Projet a Späicherfuerderunge entsprécht. Benotzt de abegraff Bonus Regallinks Kit Fir Regaler un der Spëtzt oder Säiten vun Ärer Workbench ze addéieren. Vue méi grouss. 2X4Basics Workbench Assemblée Kit Op ee Bléck hëlleft Iech eng personaliséiert Workbench mat enger Héicht vun 36 Zoll Assemblée A manner wéi enger Stonn All Regal hält bis zu 1.000 Pond (400 Kilogramm). Dëse Do-It-Yourself System léisst Iech eng Bänk erstellen, déi genee Gréisst ass, déi Dir wëllt bis 8 x 4 Féiss, andeems Dir just Holz bäidréit (net abegraff). D'Assemblée ass onheemlech einfach, dank den abegraffen, einfach ze verfollegen Instruktiounen a Schnëttlëschten. Alles wat Dir braucht ass en ugedriwwen Schrauber an e Sawno Aner Tools sinn néideg. Fir bäigefüügt Komfort, nëmmen riichtaus, 90-Grad Schnëtt sinn erfuerderlech keng Miter oder Wénkel an all Hardware déi Dir braucht ass am Kit abegraff. Wann d'Assemblée fäerdeg ass, wäert d'Aarbechtsfläch Héicht ongeféier 36 Zoll (90 Zentimeter) moossen. Fortgeschratt Engineering meets staark, haltbar Konstruktioun Robust 2X4 Framing an fortgeschratt Engineering maachen dëse Kit méi staark a méi stabil wéi déi meescht aner Workbench Léisungen. Tatsächlech wäert all Regal bis zu 1.000 Pond (400 Kilogramm) halen. En zousätzleche Bonus, d'Materialien sinn aus Heavy-Gauge Resins gemaach a sinn Impakt- a Léisungsmëttel-resistent fir laangfristeg Haltbarkeet. Villsäiteg Design fir Pottingbänken, personaliséiert Regaler, a Späicheroptiounen Mam Workbench Assemblée Kit, Dir sidd net méi limitéiert op eng Standard-Gréisst Potting Bench, Dir kënnt eng Eenheet esou kleng wéi 2 Féiss vun 2 Féiss maachen fir als Planzenstand ze benotzen. Zousätzlech kënnt Dir den abegraff Bonus 2X4Basics Regallinks Kit benotzen fir Regaler un der Spëtzt oder Säiten vun Ärer personaliséierter Workbench ze addéieren (Zousätzlech Regalknäpper Kits getrennt verkaaft). Dir kënnt Benotzerdefinéiert Workbench a Späicherléisungen fir Äert Schlofzëmmer, Garage, Keller, Schapp oder Heem bauen. Benotzerdefinéiert Regaler wäerten och wäertvoll Späicherplatz addéieren deen Äre Projet Ufuerderunge passt. Personnaliséiert eng Aarbechtsbank fir all Aarbechtsplaz. Vue méi grouss. All Regal hält bis zu 1.000 Pond. Vue méi grouss. Léisungsmëttel resistent fir laangfristeg Haltbarkeet. Vue méi grouss. Erweidert Är Regaler a Lagerung mat sechs abegraff Regallinks. Vue méi grouss. AMAZON.COM Erstellt en Aarbechts- a Späicherplatz dee wierklech Äre Besoinen passt mam 2x4basics Workbench Assembly Kit. Dësen innovativen, do-it-yourself System léisst Iech einfach eng personaliséiert Workbench a manner wéi enger Stonn montéieren. Alles wat Dir braucht ass e Sperrholz an 2x4s an Dir hutt eng Aarbechtsbank déi all Äre Projet- a Späicherbedürfnisser entsprécht. Benotzt de abegraff Bonus ShelfLinks Kitto füügt Regaler un der Spëtzt oder Säiten vun Ärer Aarbechtsbank. View larger.2x4basics Workbench Assembly Kit Op ee Bléck * Hëlleft Iech eng personaliséiert Workbench mat enger Héicht vun 36 Zoll ze bauen * Assemblet a manner wéi enger Stonn * All Regal hält bis zu 1.000 Pounds (400 Kilogramm) * Erfuerdert nëmmen direkt, 90-Grad Schnëtt * Liewensdauer GarantieKomplett personaliséierbar, einfach ze montéieren Workbench System Dëse mécht-et-selwer System erlaabt Iech eng Bank ze kreéieren déi genau d'Gréisst ass déi Dir wëllt - bis zu 8 x 4 Féiss - andeems Dir just Holz bäidréit (net abegraff). D'Assemblée ass onheemlech einfach, dank den abegraffen, einfach ze verfollegen Instruktiounen a Schnëttlëschten. Alles wat Dir braucht ass en ugedriwwen Schrauber an eng Séi - keng aner Tools sinn néideg. Fir zousätzlech Bequemlechkeet sinn nëmme riicht, 90-Grad Schnëtt erfuerderlech - keng Miter oder Wénkel - an all Hardware déi Dir braucht ass am Kit abegraff. Wann d'Assemblée fäerdeg ass, wäert d'Aarbechtsfläch Héicht ongeféier 36 Zoll (90 Zentimeter) moossen. Advanced Engineering Meets Strong, Durable ConstructionSturdy 2x4 Framing a fortgeschratt Ingenieur maachen dëse Kit méi staark a méi stabil wéi déi meescht aner Workbench-Léisungen. Tatsächlech hält all Regal bis zu 1.000 Pond (400 Kilogramm). En zousätzleche Bonus, d'Materialien sinn aus schwéier-Jauge Resins gemaach a sinn Impakt- a Léisungsmëttelbeständeg fir laangfristeg Haltbarkeet.Versatile Design for Potting Benches, Custom Shelving, and Storage OptionsWith the Workbench Assembly Kit, Dir sidd net méi limitéiert op eng Standard-Gréisst Potting Bench - Dir kënnt eng Eenheet esou kleng wéi 2 Féiss op 2 Féiss maachen fir als Planzenstand ze benotzen. Zousätzlech kënnt Dir den abegraff Bonus 2x4basics ShelfLinks Kit benotzen fir Regaler uewen oder op Säiten vun Ärem ze addéieren Benotzerdefinéiert Workbench (zousätzlech ShelfLinks Kits getrennt verkaf). Dir kënnt personaliséiert Workbench a Späicherléisungen fir Äert Schlofzëmmer, Garage, Keller, Schapp oder Heem bauen. Benotzerdefinéiert Regaler wäert och wäertvoll Stockage Plaz dobäi datt Äre Projet Ufuerderunge passt.What's in the Box Four workbench legs, six ShelfLinks, assembly instructions, hardware, and warranty information.Customize a work bench for all jobsite.View larger.All Regal hält bis zu 1.000 Pounds.View larger.Léisungsmëttel resistent fir laangfristeg Haltbarkeet.View larger.Erweidert Är Regaler an Stockage mat sechs abegraff ShelfLinks. Vue méi grouss. VUM Produzent Dëse Do-it-yourself System léisst Iech eng Bänk kreéieren déi genau d'Gréisst ass déi Dir wëllt - bis zu 8 Fouss x 4 Féiss - andeems Dir just Holz bäidréit (Holz net abegraff). D'Assemblée ass onheemlech einfach, dank den abegraffen, einfach ze verfollegen Instruktiounen a Schnëttlëschten. Alles wat Dir braucht ass en ugedriwwen Schrauber an eng Séi - keng aner Tools sinn néideg. Fir zousätzlech Bequemlechkeet sinn nëmme riicht, 90-Grad Schnëtt erfuerderlech - keng Miter oder Wénkel - an all Hardware déi Dir braucht ass am Kit abegraff. Wann d'Assemblée fäerdeg ass, wäert d'Aarbechtsfläch Héicht ongeféier 36 Zoll (90 Zentimeter) moossen. Stabil 2 x 4 Framing a fortgeschratt Ingenieur maachen dëse Kit méi staark a méi stabil wéi déi meescht aner Workbench-Léisungen. All Regal hält bis zu 1.000 Pond (400 Kilogramm). En zousätzleche Bonus, d'Materialien sinn aus schwéiere Spuerharz gemaach a sinn Impakt- a Léisungsmëttelbeständeg fir laangfristeg Haltbarkeet. Méi gesinn

Keng Unitéiten verfügbar

EAN: 0817739010398

Kategorien Tools & Home Verbesserung, Gebai Ëmgeréits, Material Ëmgank, Workbenches,

Nëmme direkt 90 Grad Schnëtt, keng Mier oder Wénkel Schnëtt néideg. Personaliséierbar Aarbechtsbänk a Regaler. Klammeren aus schwéierem Jauge strukturelle Harz. Workbench Been fir eng Workbench an all Längt oder Breet bis zu 8 Fouss x 4 Fouss (2,4m x 1,2m) ze maachen. Ëmfaasst 4 Workbench Been, 6 Regal Links. Lumber net mat all Kit abegraff (Regaler net abegraff).
Assembly Required ‎Yes
Base Type ‎Legs
Batteries Included? ‎No
Batteries Required? ‎No
Brand 2 x 4 Basics
Brand ‎2 x 4 Basics
Color Hopkins 90164 2x4basics Work Bench and Shelving Storage System
Color ‎Hopkins 90164 2x4basics Work Bench and Shelving Storage System
Customer Reviews 4.6 4.6 out of 5 stars 6,725 ratings 4.6 out of 5 stars
Finish ‎Painted
Finish Type ‎Painted
Included Components ‎4 Workbench Legs, 6 Shelf Links, accessories for assembly
Is Discontinued By Manufacturer ‎No
Item Dimensions LxWxH 34.5 x 96 x 36 inches
Item Dimensions LxWxH ‎34.5 x 96 x 36 inches
Item model number ‎90164MI
Item Package Quantity ‎1
Item Weight 0.45 Pounds
Item Weight ‎0.45 Pounds
Item Weight ‎7.2 ounces
Manufacturer ‎Hopkins Manufacturing Corporation
Material Plastic
Material ‎Plastic
Part Number ‎90164
Pattern ‎Work Bench
Product Dimensions ‎34.5 x 96 x 36 inches
Product Dimensions ‎34.5"D x 96"W x 36"H
Size ‎PACKS
Style ‎Work Bench with Shelf

3.7

10 Review
5 Star
80
4 Star
12
3 Star
3
2 Star
1
1 Star
4

Schreift Är Bewäertung

Är E-Mail gëtt net publizéiert. All obligatoresch Felder sinn markéiert mat*

Scritto da: Randy Knowles
Great result for a 1st time DIY'er
I have very little experience as a do-it-yourselfer working with wood. None-the-less, I got a GREAT result with this. Since you buy all the wood youself to put this kit together, this means you can custom design and build this to your exact needs and specifications - up to the maximums specified by 2x4Basics. This is a HUGE advantage. In my case a little careful forethought and time with a tape measure revealed that I could fit a 7' x about 25" workbench neatly into a space between 2 poles next to my basement stairs. This is a nice trick as my basement space is very limited. While I was waiting for the delivery of my kit, I visited the 2x4Basics website and downloaded the instructions to peruse. While these are only pictures, with careful examination most assembly steps become clear. I did encounter a few pitfalls, however. TABLE 1) The total dimention the depth of the workbench is the lenght of the front-to-back side pieces PLUS the width of the front and back 2x4's (side-to-side). In my case my side pieces were 24", but my total front-to-back depth wound up being 27". 2) The 23/32" AC plywood that I purchased for the table top (7' x 27") was slightly warped. Therefore I bought #6 x 1-1/4 Galvanized Deck Screws to hold down the edges of the table top. I put them in at every 1 foot, and a little pressure with my electic drill/screwdriver resulted in these being nicely countersunk for a flat, smooth table surface. 3) I wanted to be able to put large items underneath the table, for example, my cordless electric drill & saw set case. Therefore I OMITTED the bottom front 2x4 and both of the bottom shelves under the table. 4) This meant the that lowest 2 side pieces (front-to-back) needed to be an ADDITIONAL 1-1/2" (width of the back 2x4). In my case this meant instead of 24" (top 2 side pieces), the bottom side pieces were 25-1/2". 5) With 3 back pieces, 6 side pieces, one front piece and a 83-1/2" diagonal, plus the 23/32" AC plywood table top (7' x 27"), the table is as strudy as a ROCK. SHELVES 6) It took me a while to relize that the bottom 2 shelves have 2 full lenght and 2 shorter 2x4's to accommodate the 4 shelving uprights. These are 6-7/16" shorter, in my case, 6'5-9/16" long instead of 7'. 7) A number of the screws that are driven into the shelf kit pieces require getting your Phillips bit driver into small spaces. A BIT EXTENSION is almost certain to be necessary. 8) I made my total shelf height 31-1/2" above the top of the table (36"). I did this after trying several experiements with taller dimentions, but felt that I needed to be able to clearly see and reach what would be on the top shelf (I'm 5'10" tall). I also took into account the height of the ceiling. 31-1/2" seemed to the the maximum height that would work well with all of these considerations. 9) In my case I wanted my selves to accomodate small items that could fall in between the 1/2" gaps in the 2x4's. I therefore purchased 3 cut sheets of 1/8" Masonite Preswood as a hard shelf liner surface (7" wide x 16" deep). 2 of these (for the lower shelves) had to have additional cutouts at each of the corners to allow for the shelving uprights. After much trial and error, the dimentions of these 8 cutouts wound up being 3-3/8" wide (7' width side) x 4-1/8" deep (front-to-back side). Only a good lumber yard with the right tools (NOT just a table saw) can do this properly for you. 10) I nailed down the Masonite liners with 5/8" x #18 Wire Brads, spaced at each 1 foot. This small nail size allowed for the Masonite to be held firmly flat, while providing for negligible disruption of the flat shelf surface. GENERAL 11) If you're like me, you don't have the tools or experience to cut your own materials. You can have the lumberyard do it all for you. This requires, however, careful forethought and a detailed Bill of Materials. In my case, my revised, corrected Bill of Materials was: 2x4Basics #90164 Workbench and Shelving Kit Project 7' (wide) x 27" (deep [front-to-back]) workbench BILL OF MATERIALS v.4 TABLE 1A - Table surface - 7' wide x 27" deep x 23/32" thick (AC plywood) x 1 1B - Front & back - 1-1/2 x 3-1/2 x 7' long (no bottom front) x 5 1C - Sides - 1-1/2 x 3-1/2 x 24" long (top & middle) x 4 1C - Sides - 1-1/2 x 3-1/2 x 25-1/2" long (bottoms) x 2 1D - Diagonal - 1-1/2 x 3-1/2 x 83-1/2" long x 1 SHELVES 2A - Top shelf - 1-1/2 x 3-1/2 x 7' long (wide) x 4 2B - Bottom shelves - 1-1/2 x 3-1/2 x 7' long (wide) x 4 2B - Bottom shelves - 1-1/2 x 3-1/2 x 6'5-9/16" long (minus 6-7/16") x 4 2C - Uprights - 1-1/2 x 3-1/2 x 31-1/2" long (tall) x 4 2D - Upper shelf surface - 1/8" Masonite Temp. Preswood 7' long (wide) x 16" deep x 1 2D - Lower shelf surfaces - 1/8" Masonite Temp. Preswood 7' long (wide) x 16" deep w/4 cutouts @corners 3-3/8" wide x 4-1/8" deep x 2 HARDWARE #6 x 1-14" Phillips Galvanized Deck Screws - 1 box #18 x 5/8" Wire Brads - 1 box In my case the total for my materials was slightly over $135. The result far exceeded my expectations. While most of the steps can be done alone, a couple are MUCH EASiER with one additional person to help you, briefly. I am just delighted with the results, some difficulty in assembly notwithstanding.
Scritto da: WJD3RD
Basic bench
It's ok for what it is, I bought two. You can make a decent tabletop bench but you cant change shelving height or really make a cabinet front with drawers. I'm not sure how the legs will hold up over time, be careful moving them. With the cost of lumber plus the kit, it is cheaper to just by lumber and build from scratch.
Scritto da: Rebecca P.
Custom sizing galore
Good sturdy structure. Well over six months and its proven to be the perfect fit for my barn area. Customed to size and dimensions for specific tools. Easy to build. Easy to customize.
Scritto da: Severely Awesome
Flexible in more ways that one
I read the reviews for this and looked at other similar kits and I'm glad that I went with this one. At first it seems like a kit that is just some plastic legs is kind of silly, but having built the thing I think this is a way better product than some of the other kits I've seen for the same reasons that other reviewers say. I learned a lot building this. Chiefly is that you can't rely on squares to be square when it comes to wood. Even buying slightly higher grade wood for the shelf and work surface, there was still nearly an inch variation in what 24" is supposed to be. It is impossible to cut a perfectly square 2x4 without a miter saw (and I just have a skilsaw). Even if I had a miter saw, wood isn't straight. So the combination of all those imperfections would have made any kit (or any homemade design) that required me to also cut the legs would have been WAY harder to get a good finished product that didn't wobble or anything. Hence my headline. The resin is surprisingly flexible while still being very strong. I could bend/twist the legs enough so that everything actually went together tightly. There are still gaps in some spots, but much less bad than if I had cut the legs myself. It definitely came together in a quite sturdy way. I was impressed. It is also flexible in the design. I actually added a few more bits than in the picture I took, but there's really a lot of different ways you could build the bench with this kit. Whatever size you want really. I deviated from the sample plans that came with it in dimensions and it was still a good result. I think you could really get creative if you wanted to. I only have two complaints. One which I saw in the reviews: The wood screws that come with it are crappy. A few of them broke on me when tightening. They also don't want to back out of the holes after the break because they aren't threaded all the way (which is typical of a wood screw but makes it so they just spin instead of coming out). It also didn't come with enough extra screws to actually attach the shelves or table top - only the exact number to affix the 2x4s. So, fortunately I had a handful of deck screws that let me finish it, then went and bought some more for the added supports I put under the shelf for more stability. If the thing came with more and better screws it would be even easier. My only other complaint is that it would have been really nice, for the L-shape design, for there to be a sort of reverse leg in the kit for the inside of the L. I ended up adding a 2x4 leg there for extra stability as I'll be putting weight/force on that area. This was not hard to do, but it just doesn't really match the rest of the legs. I would give it a 4.5 stars if I could. If you want to build your own bench I really think this is your best bet if you're not a very experienced woodworker with lots of tools. Aside from these two minor complaints it was great. Now, the cost of wood these days is another thing entirely. It costs me $250 in wood to finish the bench. Still cheaper than buying furniture but damn.
Scritto da: Picky One
Nice kit!
This kit makes it really easy to make a workbench. It's astonishing that I paid $57 for this in 2016 and it more than doubled since! I don't understand.... Even with inflation how this has more than doubled in price! I don't see how they can justify asking $117 for pieces of plastic. Don't get me wrong, it's a great product! I just don't understand the price... ????‍♂️
Scritto da: JS
Excellent work bench.
You can build a workbench to virtually any size you want. Easy to put together, lots of advice and instructions either provided or on you can find on you tube. You could probably build a workbench cheaper, but this was easy and quick and fun to do. It does look very good when finished.
Scritto da: Chevy4240
New work bench complete with 2X4 basics kit
This 2X4 Basic kit is great !! easy to work with and you even get all the screws lol... You can build any size you like but I chose to make a 24" X 60" with double top shelf and peg board rear and it all worked out great , I would buy another kit for sure and the price was right at $99.00
Scritto da: the ick boy
Exactly what I needed
I bought this to use as a workbench in my shop. I had a great afternoon with my son constructing this. Very easy to assemble. If I'm going to nitpick a bit - the instructions were in very fine print. It was difficult to read parts of it. The bonus was that it was a pretty straight-forward build - we figured it out.
Scritto da: Generally Happy Amazon Customer
Better than expected
It's more solid than I expected. Could have made the bench without it, but they look cool and that's what matters Great product!!! Just assembled my second one, awesome fun build.
Scritto da: Jacky M de Lopez
Muy buen producto.
Excelente producto y a muy buen precio. Sin embargo no nos fue nada facil encontrar las madera deacuerdo a las especificaciones del instructivo. Lo ideal es irse directo a una madereria. Nos gusto mucho que uno le el ancho que requiera.

Zesummenhang Produiten

hot
BORA Centipede Klappt Dësch Top fir Bora Centipede Work Stand Saw Päerd - 24 Zoll x 48 Zoll - Enthält Holz Top + 6 Quick-Twist Schleisen fir e Portable, Quick Setup Aarbechtsdësch oder Workbench, CT22N Brown
3.5/5

€ 217.15

BORA Centipede Klappt Dësch Top fir Bora Centipede Work Stand Saw Päerd - 24 Zoll x 48 Zoll - Enthält Holz Top + 6 Quick-Twist Schleisen fir e Portable, Quick Setup Aarbechtsdësch oder Workbench, CT22N Brown
3.5/5

€ 217.15

hot
BLACK+DECKER Workbench, Workmate, Portable, hält bis zu 550 lbs, vertikal an horizontal Spannoptiounen, fir DIY, Holzaarbecht a méi (WM425-A) 550 lb Kapazitéit Workbench
3.4/5

€ 396.13

BLACK+DECKER Workbench, Workmate, Portable, hält bis zu 550 lbs, vertikal an horizontal Spannoptiounen, fir DIY, Holzaarbecht a méi (WM425-A) 550 lb Kapazitéit Workbench
3.4/5

€ 396.13

hot
POWERTEC UT1002 Universal Tool Stand Tool Stand, 500lbs Stand
3.4/5

€ 192.08

POWERTEC UT1002 Universal Tool Stand Tool Stand, 500lbs Stand
3.4/5

€ 192.08

hot
Stupell Industries Urban City Architecture Building Blue Owend Beliichtung, Design vum Noah Bay Grey Framed 24 x 30
0.1/5

€ 179.35

Stupell Industries Urban City Architecture Building Blue Owend Beliichtung, Design vum Noah Bay Grey Framed 24 x 30
0.1/5

€ 179.35

hot
POWERTEC 71132V Quick-Release Workbench Caster Platen, 4-Pack
3.4/5

€ 49.16

POWERTEC 71132V Quick-Release Workbench Caster Platen, 4-Pack
3.4/5

€ 49.16

hot
Professionelle Qualitéitsprodukter 26 "x 32" Heavy Gauge Stahl Wandmontéiert Klapp Workbench "Lock N Load" fir Plaz ze spueren an der Garage, Déngschtraum, Kichen, Wäschzëmmer, Fabriken a Schapp FB2632P
3.9/5

€ 543.44

Professionelle Qualitéitsprodukter 26 "x 32" Heavy Gauge Stahl Wandmontéiert Klapp Workbench "Lock N Load" fir Plaz ze spueren an der Garage, Déngschtraum, Kichen, Wäschzëmmer, Fabriken a Schapp FB2632P
3.9/5

€ 543.44

hot
BLACK+DECKER Workbench, Aarbechtsdësch, portabel a versatile (BDST11552)
0.1/5

€ 191.36

BLACK+DECKER Workbench, Aarbechtsdësch, portabel a versatile (BDST11552)
0.1/5

€ 191.36

hot
Schwäizer Madison Well Made Forever SM-CH06BG, Toilette Hardware Rose Gold (SM-WT442, SM-WT450, SM-WT455, SM-WT514, SM-WT530)
0.1/5

€ 38.77

Schwäizer Madison Well Made Forever SM-CH06BG, Toilette Hardware Rose Gold (SM-WT442, SM-WT450, SM-WT455, SM-WT514, SM-WT530)
0.1/5

€ 38.77

Entdeckt eisen internationale Netzwierk

Mir schécken an 28 Länner, iwwer 200.000 Produkter. Bleift aktualiséiert, abonnéiert Iech op den Newsletter.

Array

Ganzen:€ 0.00

Kuckt de WeenchenOfmellen

Kategorien

All d'Kategorien
Menu Kategorien Noper Weenchen

Menu