0
0

Ganzen:€ 0.00

Kuckt de WeenchenOfmellen
LoginRegister
0

Ganzen:€ 0.00

Kuckt de WeenchenOfmellen
LoginRegister

Drill America - POU1/2NPTW/DRILL 1/2 Carbon Steel NPT Pipe Tap and 23/32 High Speed ​​Steel Drill Bit Set, POU Serie 1/2 NPT 1/2 NPT Tap - 23/32 Drill

Brand:Drill America

3.7/5

€
35.99

1/2 Carbon Steel NPT Tap an 23/32 HSS Drill Bit Set, 1/2 NPTTap Informatioun: Drill America dwtpt Serie Qualtech Kuelestoff Stahl Pipe Tap ass entwéckelt fir beschiedegt oder Stau Pipe thread ze botzen an / oder nei ze threaden. Et ass gëeegent fir eng breet Varietéit vu Materialien souwuel ferro wéi net-ferro ze threaden. Déi nominell Gréisst vun engem Päif Tap ass déi vum Päiffitting fir ze tippen, net déi tatsächlech Gréisst vum Tap. De Fuedem tapert 3/4 Zoll pro Fouss. All Päif Krunn mat engem 2-1/2 bis 3-1/2 thread chamfer ausgestatt. Npt Threads erfuerderen d'Benotzung vun engem Sealer wéi Teflon Band oder Päifverbindung. Onbeschichtete Tools weisen just de Basissubstrat ouni zousätzlech Behandlung oder Beschichtungen a si passend fir eng breet Palette vun Uwendungen. Ronn mat véiereckege Enn Shank. Riichtaus Flute Tools erlaben Chips an de Flutes ze sammelen wéi se schneiden a si gutt fir déi meescht Uwendungen a Shallow Schnëtt gëeegent. Riets-Hand Schnëtt Tools hunn eng Schneidaktioun déi engagéiert wann se an der Auer Richtung lafen. Drill Bit Informatioun: Drill America dwdn Serie Héichgeschwindeg Bohrbit ass en zouverlässeg, allgemeng Zweck Bohr entwéckelt fir an enger breeder Palette vu Materialien an den Eisen- a Stolfamilljen auszeféieren. Ideal fir Produktioun, Ënnerhalt oder portable Bueraarbechten. Uewerfläch behandelt mat abrasion-resistente schwaarzen Oxid. Schwaarzoxidbehandlung füügt Schmieregkeet a kreéiert kleng Taschen op der Uewerfläch vum Tool, deen d'Kühlmëttel no bei der Schneidekant halen. Ronn Shanks erlaben Benotzung mat enger grousser Villfalt vun Tool Holding Systemer. Wann Dir am Géigesaz Richtung (riets Schnëtt) leeft, spiralgeschnidde Tools evakuéiere Chips erop an aus dem Schnëtt fir d'Verstoppung ze reduzéieren.

Keng Unitéiten verfügbar

EAN: 0887861241854

Kategorien Industriell & Wëssenschaftlech, Schneid Tools, Tappen, Pipe Taps,

Set enthält passende NPT Päif Krunn an Héichgeschwindeg Stahlbohrer. De Set kënnt an engem Plastikbeutel. 1/2 Kuelestoff Stahl NPT Krunn an 23/32 HSS Bohrer mat 1/2 Shank. Schwaarzoxidbohrer ass ideal fir Produktioun, Ënnerhalt oder portable Bueraarbechten. Kuelestol Pipe Krunnen sinn entwéckelt fir beschiedegt oder Jam Pipe thread ze botzen an oder nei ze threaden.
Brand Drill America
Country of Origin China
Finish Type Uncoated
Item model number POU1/2NPTW/DRILL
Manufacturer Drill America
Material Carbon Steel
Package Dimensions 8.9 x 6.54 x 0.71 inches; 9.92 Ounces
Shank Type Round with Square
Tool Flute Type Spiral

3.7

13 Review
5 Star
79
4 Star
12
3 Star
5
2 Star
1
1 Star
3

Schreift Är Bewäertung

Är E-Mail gëtt net publizéiert. All obligatoresch Felder sinn markéiert mat*

Scritto da: Joe
Worked great
This worked fantastic on my 67 Corvette's Muncie transmission. The fill plug had seized so badly that it broke off. I was doing a clutch and had the transmission out of the car, so I drilled the plug out and re-threaded it using this product. I even put an additional drain plug in and used this to drill and thread that, too! It worked so good that I can now drain and fill the transmission while it's in the car. Of course, I took the side cover off and cleaned out the the transmission, flushed, and refilled with new gear oil.
Scritto da: T. Johnson
It worked in my application
Everything went great, job done.
Scritto da: Amozon shopper. Researcher of everything.
Decent
It’s a decent bit for home use. I would not expect to use for everyday work. Use with some cutting oil and it really works well.
Scritto da: DrPeckrr
Great kit for drilling/tapping 1/8th npt
Used it to drill/tap an end cap on my fuel line so I could add a 1/8npt spot to attach a secondary fuel pressure sensor. Awesome!
Scritto da: Minerba B.
Worked for me
Sharp and functional! Needed to tap two 1/4" holes in a magnesium/aluminum case. Drill bit was sharp and cut the holes quickly. The tap was just as sharp and threaded nicely. Glad I added this to my tool box.
Scritto da: Jim C So Cal
Tap and drill bit
The drill bit is the cheapest drill but I’ve seen. The tap worked okay after I used another drill bit to make the hole. Got the job done but not the best quality.
Scritto da: Donald Vitale
Twist drill is fine, Tap is terrible.
Hey, it's cheap...but the tap is terrible. I couldn't even get through 1/4" aluminum . Had to finish it with an old Greenlee tap. Drill is worth it.
Scritto da: Paul Millner
Drill bit shank is 1/2”
Caution, reduced shank drill bit, sure… but only reduced to 1/2” which is too large for the drill motors I could comfortably use at this specific job site. Have purchased 3/8” shank bit from others, wish me luck!
Scritto da: Asterixx
Tap is not good quality. I got what I needed done, but barely, and now it's no good.
I should have paid attention to the negative reviews. I bought this because I had to drill and tap two holes in a piece of 1/4" mild steel. The drill bit went through OK (I started out with a small bit and worked my way up to this one, as is the norm, and the bit still had a good edge on it after the two holes). The tap, however, is garbage. I got the first hole tapped and there was very noticeable damage to the tap. I managed to get the second hole tapped as well, but it was a struggle, and then the tap was difficult to remove from the hole because the damaged threads on it were trying to ruin the new threads I had just made. Remember, this was in 1/4" mild steel. I couldn't imagine trying to use it in cast iron, or anything harder than brass, really. The tap is no longer usable. I got my two holes done, but barely.
Scritto da: Perry J Moreau
Great Combination
Drilled and tapped a hole on top of Manifold (F150) for a Heater Hose fitting. The Manifold is made from aluminum and this combination worked perfectly for me, just remember to lubricate both the hole and the tap. Did the repair with the manifold cover still on the vehicle by using an 18" torque wrench with a long extension and 17mm socket, worked like a charm. Used the socket and torque wrench because I was not able to find a suitable sized tap wrench that will fit the taps 1/2 inch square end. Many tap wrenches claim to accept 1/2 inch taps but do not open wide enough to insert a 1/2 inch square peg. I found this out the hard way and now have two new tap wrenches in my tool box. John Perry
Scritto da: Wayne Dale
Inferior Quality
I have been a maintenance mechanic for many years and needed this size to add to my tools. Unfortunately I was extremely disappointed with the quality of steel in this tap. Using the supplied drill and proper threading oil it failed. After only having 7-8 threads in one flute broke with very little pressure. Look at the color in the break, definitely low quality steel or bad hardening process. I will be returning it for a full refund and look for something better.
Scritto da: Chris mulhall
Wrong size packaged in listed size container.
Good bit. Good tap. Just be cautious of the size. I ordered 1/4npt kit and got a 1/8npt kit. The package even said 1/4. Luckily it was smaller than I needed so I could resize larger, but if it was in reverse I could have been detrimental as I was drilling a diff housing for ARB air locker. Just double triple check before use.
Scritto da: Rex Havoc
Drill broke first time within a second
Might have "America" in the name, but it's not of the quality you expect from a made in America product. The tap worked ok.

Zesummenhang Produiten

hot
3.6/5

€ 60.54

3.6/5

€ 60.54

hot
IRWIN NPT Tap, 1/2-14 (1905ZR)
3.6/5

€ 38.01

IRWIN NPT Tap, 1/2-14 (1905ZR)
3.6/5

€ 38.01

hot
Century Drill & Tool 97204 Carbon Steel Pipe Thread Tap, 1/2-14NPT
3.8/5

€ 39.53

Century Drill & Tool 97204 Carbon Steel Pipe Thread Tap, 1/2-14NPT
3.8/5

€ 39.53

hot
Century Drill & Tool 97208 High Carbon Steel National Pipe Tap, 1-1/2-11 1/2 NPT
4.1/5

€ 104.36

Century Drill & Tool 97208 High Carbon Steel National Pipe Tap, 1-1/2-11 1/2 NPT
4.1/5

€ 104.36

hot
HHIP 1011-3306 6 Stéck NPT Taper Pipe Tap Set, 1/4~1-1/4 Zoll 1/4-1-1/4 6 Stk. Tippen op Set
3.8/5

€ 702.39

HHIP 1011-3306 6 Stéck NPT Taper Pipe Tap Set, 1/4~1-1/4 Zoll 1/4-1-1/4 6 Stk. Tippen op Set
3.8/5

€ 702.39

hot
Drill America DWTPT1/4-1-1/4SET 6 Stéck NPT Pipe Tap Set an Holzkëscht (1/4, 3/8, 1/2, 3/4, 1 an 1-1/4), Carbon Steel, DWT Serie, Onbeschichtet (Hell), Kleng
3.4/5

€ 117.09

Drill America DWTPT1/4-1-1/4SET 6 Stéck NPT Pipe Tap Set an Holzkëscht (1/4, 3/8, 1/2, 3/4, 1 an 1-1/4), Carbon Steel, DWT Serie, Onbeschichtet (Hell), Kleng
3.4/5

€ 117.09

hot
Drill America 1-1/4 BSPS High Speed ​​Steel Straight Pipe Tap, DWT Serie DWTBSPS1-1/4 1-1/4 British Standard Pipe Tap
3.5/5

€ 335.33

Drill America 1-1/4 BSPS High Speed ​​Steel Straight Pipe Tap, DWT Serie DWTBSPS1-1/4 1-1/4 British Standard Pipe Tap
3.5/5

€ 335.33

hot
Drill America - DWTPT1/8-1SET 6 Stéck NPT Pipe Tap, Carbon Steel, DWTPT Serie Set, 1/8, 1/4, 3/8, 1/2, 3/4 an 1 an Holzkëscht
3.6/5

€ 80.49

Drill America - DWTPT1/8-1SET 6 Stéck NPT Pipe Tap, Carbon Steel, DWTPT Serie Set, 1/8, 1/4, 3/8, 1/2, 3/4 an 1 an Holzkëscht
3.6/5

€ 80.49

Entdeckt eisen internationale Netzwierk

Mir schécken an 28 Länner, iwwer 200.000 Produkter. Bleift aktualiséiert, abonnéiert Iech op den Newsletter.

Array

Ganzen:€ 0.00

Kuckt de WeenchenOfmellen

Kategorien

All d'Kategorien
Menu Kategorien Noper Weenchen

Menu