0
0

Ganzen:€ 0.00

Kuckt de WeenchenOfmellen
LoginRegister
0

Ganzen:€ 0.00

Kuckt de WeenchenOfmellen
LoginRegister

GEARWRENCH 114 Stk. SAE / Metric Ratcheting Tap and Die Set - 82812 114 PC Set

Brand:GEARWRENCH

3.8/5

€
430.51

PRODUKTBESCHREIWUNG Dëse komplette Set vu SAE Standard a Metric GEARWRENCH Krunnen a Stierwen ass perfekt fir de Meeschter Mechaniker oder Maschinnebuttek deen eng breet Varietéit u Threading brauch. 48 Krunnen an 48 Stierwen bidden Iech all néideg Gréisst, an eis Tools sinn aus dem Buedem entworf fir GEARWRENCH Innovatiounen un eis haart schaffende Benotzer ze bréngen, wéi de 5 Ratcheting Kapp vun eisen T Handle oder de patentéierte Twist Lock Guide System deen all séchert. Verlängerung oder Schneidinstrument zum Grëff, produzéiert riicht Fuedem op all Schnëtt. AMAZON.COM Komplett Set vu Ratcheting-T-Griff-System vun Tap- a Stierf-Tools (méi grouss kucken).Den 114-Stéck GearWrench Tap and Die Set (Modell 82812) ass ideal fir an enk, ageschlossene Beräicher ze benotzen, an de patentéierte Twist Lock Guide System reduzéiert Réckgang vun stierwen Guide an hält stierwen zentréiert iwwerdeems thread opzedeelen. De Ratcheting T-Schlüssel bitt e 5-Grad Ratcheting-Arc, a säi reversiblen Hiewel erlaabt séier Ännerunge vu vir bis zréck fir d'Hand-iwwer-Hand-Wendung ze eliminéieren. WAT ASS AN DER BOX82800 grousse Ratcheting T-Schlüssel, 82801 grousse Sperrkraaftadapter, 82802 grousse Hex-Stäreadapter, 3881 mëttel Ratcheting T-Schlüssel, 3883, mëttlere Kranadapter, 3882 klenge Krunnadapter, 3884 mëttlere Kranadapter, 3884 mëttlere Stréimadapter, 4803 weiblech Verlängerungsadapter, rutschen T fir Adapter, 4mm Hex Schlëssel, 5 Schrauwen Extractoren, Metresch Fuedem Jauge, SAE Fuedem Jauge, 48 Krunn an 48 Dies. Sockets, Schrauber / Nuttdreiwer, Zangen a Spezialgeschir. Egal wéi d'Industrie wou Dir Iech fannt, GearWrench huet d'Tools fir Är Bedierfnesser ze passen - vun der präzis bis zum bal onverständlechen. GearWrench Handwierksgeschir si garantéiert fir d'Liewen fräi vu Mängel a Material a Veraarbechtung.82812 114 PIECE LARGE COMBINATION TAP AND DIE SETAT A GLANCE * Patented Twist Lock Guide System reduces backwalk of die guide * Reversibelen Hiewel eliminéiert Hand iwwer Hand dréien * Kuelestol Konstruktioun * Liewensdauer Garantie VUM Produzent Gear Wrench 114-Stéck grouss Ratcheting Krunn an Diät Set SAE / Metresch, besteet aus: 82800 grouss Ratcheting T Schlëssel, 82801 grouss Sperrkran Adapter, grouss 82802 Hex Die Adapter, 3881 Medium Ratcheting T Wrench, 3883, Medium Tap Adapter, 3882 kleng Tap Adapter, 3884 Medium Die Adapter, 82803 männlech Extensioun Adapter, 82804 Weiblech Extensioun Adapter, Rutsch T fir Adapter, 4mm Hex Schlëssel, 5 Schrauwen Extractoren, metresch thread gauge, SAE thread gauge, 48 Krunn an 48 stierwen. Komplette Set vu 48 Krunnen a 48 Stierwen, plus kleng, mëttel a grouss System vu ratcheting T Handle, Sperrkranadapteren an Hex Dier Adapter. Krunnen a Stierwen sinn aus héichqualitativen Kuelestofftool Stahl gemaach. Gear wrenches ratcheting -I Grëff Systemer si perfekt fir de Meeschtesch Mechaniker oder Maschinn Shop. De Set kënnt mat geblosenem Fall fir sécher an organiséiert Lagerung. Méi gesinn

Keng Unitéiten verfügbar

EAN: 787721817901

Kategorien Tools & Home Verbesserung, Power & Handwierksgeschir, Handwierksgeschir, Taps & Dies, Tap & Die Sets,

Drive Extension Adapter bidden e gréisseren Zougang zu ageschlossene Gebidder wann se mat 3/8inch Drive Extensions benotzt ginn. Automatesch Sperrfunktioun erlaabt datt d'Tapadapters sécher ewechgeholl kënne Blowform Droenkoffer mat gekippten Krunnhalter fir einfach Zougang a Späichere Set enthält 2 Ratcheting T Handle, 3 Gréisste Tapadapter an 2 Gréisste vum Die Adapter, 2 Extensiounsadapter an e rutschen T fir d'Adapter, e 4mm Hex Schlëssel, 5 Schrauwen Extractoren, SAE a metresch Fuedem Gauges, an 48 Krunn a Stierwen an SAE a metresch Gréissten rangéiert vun 4 40 bis 3/4 "an 3mm bis 18mm. Die Adapter funktionnéieren mam 3/8 Zoll Drive Pass duerch Ratchet a Socket System souwéi Socket Accessoiren. Ratcheting t Wrench funktionnéiert mam GEARWRENCH Passthru Socket System. Twist Spär Guide System reduzéiert de "zréck goen" vun der stierwen Guide an hält de stierft zentréiert iwwerdeems opzedeelen. Ratcheting T Handle Wind Dies mat engem 5 ° Schwenkbogen an hunn e Reversibele Hiewel fir d'Hand iwwer Hand ze dréinen.
Batteries Included? ‎No
Batteries Required? ‎No
Color ‎As Shown in the Picture
Country of Origin ‎Mexico
Customer Reviews 4.7 4.7 out of 5 stars 3,959 ratings 4.7 out of 5 stars
Domestic Shipping Item can be shipped within U.S.
Finish ‎Full Polish Chrome; taps & die are untreated
Included Components ‎
International Shipping This item can be shipped to select countries outside of the U.S. Learn More
Is Discontinued By Manufacturer ‎No
Item model number ‎82812
Item Package Quantity ‎1
Item Weight ‎1.3 pounds
Manufacturer ‎GearWrench
Material ‎Steel
Measurement System ‎SAE & Metric
Part Number ‎82812
Power Source ‎Hand Powered
Product Dimensions ‎21 x 13 x 3 inches
Shape ‎Rectangular
Size ‎114 PC
Style ‎Set
Usage ‎Professional
Warranty Description ‎No Warranty - Consumable

3.8

13 Review
5 Star
82
4 Star
12
3 Star
3
2 Star
1
1 Star
2

Schreift Är Bewäertung

Är E-Mail gëtt net publizéiert. All obligatoresch Felder sinn markéiert mat*

Scritto da: OZ4
Works Great
Works as advertised!
Scritto da: nick radakovich
Value
Where I work taps are important an the quality is a must
Scritto da: Kenn
6 years and counting
Had these for six years and use them all the time as I restore a classic beetle to chase threads and other small projects. It’s a great set. The ratcheting handles are great, it’s all of great quality. Love this set.
Scritto da: Whilly whips
Worked great
Worked great as expected!
Scritto da: Tex
A great set with a lot to offer for this home-user.
I had read the reviews here before purchasing and especially took note of the people that reported some gouges in some of the machined taps with this set. I ordered anyway for a couple of reasons. First, this is no small company. It is part of Apex Tools that owns Lufkin Tapes, Crescent Tools, Wiss cutting tools, Nicholson Files and more etc that go back over 100 years. I have all of those tool Brands at home and they have served me exceptionally well for 30-40 years. So, I figured I'd give this set a go and if it was totally unacceptable, I could always return it (thanks to Amazon's service). Bottom-line, its not going back... I'm a home/hobbyist user of Tap and Dies, but I can understand why a Professional who uses these tools in a daily business setting can feel differently about what they need. But for my use at home, this is a great set, and for what you get, a very good price. I could not touch an equally configured Irwin/Hansen set for this price point. I have also used this set and it does a very acceptable job for my needs. Regarding the reports of the small gouges in some of the larger Taps, yes I have those too. But it is only on a couple of the Taps, the gouges are small, and the gouges are not on the cutting edges of the Taps. The cutting edges are clean, in tact and sharp. The very few gouges are on the threaded following surfaces, so that problem (for me) will not affect the tool's ability to cut proper threads. I did find that I needed to clean out a few loosely attached burrs from a couple of the Taps when they were machined. A small brass brush or even the "thread gauges" that come with this set easily dispatched those burrs. I have already used some of the Taps and they cut very well. The accessories that come with this set are quite remarkable and they work well too. I especially like the Tap Adapters that come with this set and they way they lock into the T-wrenches. My only complaint about the T-wrenches is that I can't lock the ratchet into place. You either go forward or backward via the selector flip/switch. If you have done much tapping of harder metals, you know that going forward and back quite often is needed to dislodge the burrs that you cut. I can accomplish it with the flip-lever, it would just be easier (at times) if the T-wrench didn't ratchet. But for cutting soft metal, I love that ratchet and the ability to move the handle without changing my grip is very appreciated. Overall, I think this set is a winner. I understand that it is not an Irwin/Hansen or even higher quality set. But for my use, that is OK and I expect to get many years of use from this set. I already have a much smaller, very cheap quality Tap and Die set that I've owned for 30+ years. Take care of your tools, use some finesse vs brute force, use cutting fluid, etc. and you can get many years even from a lesser quality Tap and Die set. :^) One update (4/23/16): I also purchased the Gator Tools V-Tap Guides that help keep the tap vertical (especially when starting the threads). The Gator Tools Tap Guide is a well made/machined part that earns a full 5-stars all by itself. Unfortunately, for this particular Tap set from GearWrench, on their smaller Taps (the Metric M5 and smaller) and (the Standard #10 and smaller), these Taps will not pass through the Big Gator Tools Tap Guide. That is because GearWrench makes the barrel (above the cutting portion of the Tap) slightly larger. Because of that design on their smaller Taps, it prevents the Tap from passing through the Big Gator Tape Guide. I've looked at these sizes in the Irwin Taps and it appears that Irwin maintains the barrel diameter so that it is not larger than the cutting portion diameter of the Tap. If something like this is important to you, then it may be worth considering Irwin vs GearWrench. I'm still happy with my GearWrench set and have some older Taps that will pass through the Big Gator tool just fine. Just thought I'd mention it as a difference for those considering this GearWrench set.
Scritto da: 338 Lapua Shooter
Good kit and good value
I purchased this kit about 5 years ago because I didn’t want to bring my snap on tap and die set to my shop where they would surely get lost or stolen by my staff. I didn’t have exceedingly high expectations of the kit but to be honest it’s just as good. As with any set you need to use a light cutting oil and as such I always use a thin oil. Over the years I have broken many bits and pieces of these types of kits, even my snap on ones and they always replace them…. But I have yet to break one of these. When I got my snap on brand products I was in the aftermarket automotive industry so I used them on a more routine basis, but now shifting careers to firearms I use different thread patterns and mostly the smaller ones which are far more prone to break, but these never have broken. To be entirely honest I paid almost half the price that they currently are selling for right now and since they’ve worked so well for me I’d have zero hesitation to buy a new set should I need them. The “big truck” brands I don’t think are any better and surely not worth the inflated cost which is likely 3-5 times as much as this kit. You’ll be happy with the kit.
Scritto da: Dexter See
Very good
Very good
Scritto da: Dustie Rose
High quality at a cheap price
For $210 I am extatic. This 114pc set performs just as good as my Snap-On set that has only HALF of the contents as this 114pc set and is twice the price. The ratcheting tap handles are elite, definitely a game changer when it comes to tight spots. Overall, I am very impressed with how these tap and die perform on both mild, stainless, and even aluminum. I would highly recommend this set to anyone.
Scritto da: ali
Very good
Great quality, love the ratchet
Scritto da: Laurence
Would love a refund or replacement
There seems a lot of play in the ratchet mechanism, and the ratchet direction lever has little resistance so when your removing the tap quickly the ratchet leaver keeps changing direction on its own account, this is extremely annoying,
Scritto da: Aivaras Ceida
Useless thing
Complete peace off ... Second time i used it and the centre ratchet mechanism fell out and i lost pressure spring
Scritto da: Mixx Cheang
Amazing!!
Very sharp and precise, bought a set of lang and did not fix a cross tread bolt almost snap the tool. Return it and bought gw tap and die set and work perfectly. Very happy with that tool safe a lot of time with the right tools.
Scritto da: MECANO
MECANO
bonjour l'outil est bien fait pour les endroit étroit merci.

Zesummenhang Produiten

hot
Greenfield Threading 330083 High Speed ​​Steel Jobber Drill Plug Hand Tap Set (18-Stéck Set)
4.1/5

€ 151.04

Greenfield Threading 330083 High Speed ​​Steel Jobber Drill Plug Hand Tap Set (18-Stéck Set)
4.1/5

€ 151.04

hot
Lang Tools 2581 26-Stéck Thread Restorer Tap and Die Set, schwaarz
3.5/5

€ 88.19

Lang Tools 2581 26-Stéck Thread Restorer Tap and Die Set, schwaarz
3.5/5

€ 88.19

hot
Drill America 1/4 - 1-1/8 Tap Capacity Adjustable Tap Wrench, DWT Serie DWTTW7 1/4 - 1-1/8 Hand Tap
3.2/5

€ 64.84

Drill America 1/4 - 1-1/8 Tap Capacity Adjustable Tap Wrench, DWT Serie DWTTW7 1/4 - 1-1/8 Hand Tap
3.2/5

€ 64.84

hot
Greenlee 1430AV DIE-2-1/2 IPS (074MM) (738)
3.4/5

€ 120.55

Greenlee 1430AV DIE-2-1/2 IPS (074MM) (738)
3.4/5

€ 120.55

hot
3.5/5

€ 21.87

3.5/5

€ 21.87

hot
BOSCH BPT7M100 7mm - 1.00 High-Carbon Steel Metric Plug Tap
3.4/5

€ 22.15

BOSCH BPT7M100 7mm - 1.00 High-Carbon Steel Metric Plug Tap
3.4/5

€ 22.15

hot
IRWIN Hanson 12002 T-Handle Tap Wrenches, 1/4 - 1/2
3.4/5

€ 30.57

IRWIN Hanson 12002 T-Handle Tap Wrenches, 1/4 - 1/2
3.4/5

€ 30.57

hot
Irwin 8338 10mm x 1.0 Metresch Tap Gréisst: 10MM-1.0mm.
3.8/5

€ 25.21

Irwin 8338 10mm x 1.0 Metresch Tap Gréisst: 10MM-1.0mm.
3.8/5

€ 25.21

Entdeckt eisen internationale Netzwierk

Mir schécken an 28 Länner, iwwer 200.000 Produkter. Bleift aktualiséiert, abonnéiert Iech op den Newsletter.

Array

Ganzen:€ 0.00

Kuckt de WeenchenOfmellen

Kategorien

All d'Kategorien
Menu Kategorien Noper Weenchen

Menu