KegWorks-KEG730 Ball Lock Quick Disconnect - Gaz avec raccord 1/4 MFL - Gris

Brand:KegWorks

2.7/5

28.31

Cette déconnexion rapide à verrouillage à bille peut être utilisée avec des réservoirs Pepsi ou 7-up ou votre fût Cornelius homebrew. vous aurez besoin de l'écrou approprié pour vous aider à établir une connexion entre cette déconnexion et votre tuyau d'air pour une distribution correcte. c'est parfait pour les brasseurs amateurs qui échangent fréquemment des produits (bières artisanales et commerciales) qui pourraient avoir besoin d'être distribués à différentes pressions. le raccord mfl est extrêmement polyvalent et s'adapte aux exigences de pression de distribution de votre bière du moment. En stock et prêt à être envoyé. caractéristiques : connexion de verrouillage à bille. utilisé pour le gaz. spécifications : raccord 1/4 mfl intégré.

Un must pour le brasseur amateur sérieux. Facile à utiliser. Celui-ci est utilisé pour le gaz. Parfait pour les brasseurs amateurs qui aiment aussi les bières commerciales. Les déconnexions rapides de style boule sont utilisées pour la plupart des réservoirs Cornelius, Pepsi et 7-up.
Is Discontinued By Manufacturer No
Item model number KH-DOW3-T4KT
Manufacturer Home Brew Ohio
Product Dimensions 2.3 x 1.6 x 1.6 inches; 0.35 Ounces

2.7

8 Review
5 Star
50
4 Star
10
3 Star
15
2 Star
13
1 Star
11

Donnez votre avis

Votre courriel ne sera pas publié. Tous les champs obligatoires sont marqués d'un*

Scritto da: James H.
It serves its purpose
I use a ball lock for carbonating water (homemade soda stream). As a result, the ball locks I use see are connected and disconnected on a regular basis. The very first Ball Lock I purchased failed in about 12 months (bearing popped out which allowed CO2 to escape). I purchased this as a replacement. It's getting the job done right now. I suspect Ball Locks in general have a duty cycle, a number of times they are intended to be connected and disconnected. It would be helpful if this type of information was made available. I also assume that most manufactures design these beer keg connections or soda carbonation where the connections are not changed as frequently. It could be that if you are going to use this as part of a home carbonation system, no model will last that long. I will say the plastic on this model seems to be harder than my previous version, so I'm hopeful it will last longer. But as with all things, only time will tell.
Scritto da: Ross Butterworth
But the CMB disconnects are better made and can be found elsewhere for less money
These disconnects do work. These are not the CMB disconnects you're used to from major sellers or your local brew shop. They carry a logo with an "S" inside a toothed gear. They seem to be a slightly different more brittle plastic and there is some flash from the forming process. The first few times around I had to apply them with a mallet. They get the job done and I don't expect them to fail. But the CMB disconnects are better made and can be found elsewhere for less money.
Scritto da: Tony Polk
Spare parts
Bought as a backup in case one goes bad
Scritto da: Brian
Bummed it broke so soon
Air valve malfunctioned and broke. It worked for about a dozen connecting and disconnects, then just started hissing gas.
Scritto da: Michael C.
Just works
Just works
Scritto da: GTJohnson
Leaked and cost an entire 20lb CO2 tank!
Leaked and cost an entire 20lb CO2 tank! DO NOT BUY!!! Despite the mixed reviews, I purchased one of these ball lock quick disconnects to expand my CO2 manifold for my kegerator, along with a fresh new 20lb CO2 tank. Installation and everything went fine, spray test gave showed no leaks, set the regulator to 12 psi and went to bed. A couple days later I try to pour a beer and barely a trickle comes out. I swapped the regulator to my backup 5lb tank and did another spray test, only to find that this disconnect was leaking BADLY from space between the body and the plastic piece that moves up and down. Even before the spray test I could hear the hissing. Absolutely would not recommend buying one of these unless you have an unlimited supply of CO2 tanks.
Scritto da: Misfitdad
mechanism works great and seal is perfect
Exactly as described, mechanism works great and seal is perfect.
Scritto da: AndyB
Five Stars
Works great

Produits connexes

hot
Kit de brosse à fût
3.7/5

€ 50.67

Kit de brosse à fût
3.7/5

€ 50.67

Découvrez notre réseau international

Nous expédions dans 28 pays plus de 200 000 produits. Restez informé, inscrivez-vous à la newsletter.

Array