Kit de réparation de filetage hexagonal E-Z pour inserts filetés affleurants en bois tendre 1/4-20 x 20 mm, perceuse, outil d'installation affleurant 1/4-20 x 20 mm

Name: Kit de réparation de filetage hexagonal E-Z pour inserts filetés affleurants en bois tendre 1/4-20 x 20 mm, perceuse, outil d'installation affleurant 1/4-20 x 20 mm
Brand: E-Z LOK
SKU: 0847554042328
Price: 43.02 EUR
Availability: InStock

Brand:E-Z LOK

3.7/5

€
43.02

Kit de réparation de filetage E-Z LOK pour bois Kit de réparation de filetage E-Z LOK pour bois tendre. Ce kit pratique comprend des inserts filetés, une perceuse et un outil d'installation. Ces inserts filetés pour bois tendre sont parfaits pour les applications où le décapage ou l'érosion du filetage est possible. Parfait pour les meubles prêts à assembler, les poignées de tiroir, les vitrines, les caisses, partout où une fixation sera utilisée dans du bois tendre. Les inserts filetés à entraînement hexagonal E-Z fournissent des filetages de machine robustes dans les bois tendres. Ils sont dotés de larges filetages externes qui offrent une puissance de maintien exceptionnelle. Ils sont conçus pour être utilisés avec des matériaux tels que le pin, le contreplaqué, les panneaux composites et le MDF. Inserts filetés en zinc disponibles en inserts filetés hexagonaux affleurants et inserts filetés à bride hexagonale avec filetages internes de 8-32 à 3/8 et M6 à M10.

Aucune unité disponible

EAN: 0847554042328

Catégories Industriel et scientifique, Nœuds, Vis et attaches, Écrous,

LE KIT COMPREND - Le kit pratique comprend des inserts filetés pour le bois, une perceuse et un outil d'installation d'inserts filetés. À UTILISER AVEC DES APPLICATIONS - Les inserts filetés E-Z Hex pour le bois sont conçus pour être utilisés avec des matériaux tels que le pin, le contreplaqué, les panneaux composites et le MDF. Conceptions affleurantes et à brides - Inserts filetés en zinc disponibles dans des inserts filetés hexagonaux affleurants et des inserts filetés à bride hexagonale avec des filetages internes de 8-32 à 3/8 et M6 à M10. Fournissez des filetages de machine robustes – Les inserts filetés E-Z Hex Drive dans ce kit d'outils de réparation de filetage fournissent des filetages de machine robustes dans les bois tendres. Ils sont dotés de larges filetages externes qui offrent une puissance de maintien exceptionnelle. KIT DE RÉPARATION D'INSERTS FILETÉS - Kit de réparation de filetage E-Z LOK pour réparer les inserts filetés dans le bois tendre.

Country of Origin	USA
Drive System	External Hex
Exterior Finish	Zinc
Fastener Type	Flange
Item model number	Threaded Inserts
Manufacturer	E-Z LOK
Material	Zinc
Product Dimensions	8 x 3 x 2 inches; 3.49 Ounces
Thread Size	1/4-20 x 20mm

5 Star

4 Star

3 Star

2 Star

1 Star

Donnez votre avis

Votre courriel ne sera pas publié. Tous les champs obligatoires sont marqués d'un^*

Votre note

Scritto da: Kris

Fantastic for mounting 10” subs

Theses worked great for mounting my JL Audio subs in my custom box. Highly recommend these over using wood screws. You only need to drill about 1/2” deep when using 3/4” MDF. Really nice if you ever remove your sub. You don’t have to “clock” the sub like you would if you used wood screws, and no enclosure penetration.

Scritto da: Gummy

Nice kit

Difficulties going into MDF initially. When I was able to get them in, they did hold well.

Scritto da: D. King

Great for eliminating visible fasteners in your work

I used these on a studio desk so that there would be no screws showing in the finished piece. They work great! Holding power is much more than you'd expect. One thing to keep in mind is that these have a flange. This flange keeps you from inserting them too far; however, they can also keep the two connected surfaces from meeting absolutely flush. I drilled a slight (1/64th or so) countersink with a Forstner bit. This allowed them to be slightly inset and not interfere with fit. Another option would be to order the same fastener without the flange. While you can use a drill to insert them, I used a drill to get them started and an Allen wrench to set them. This eliminated stripping out the wood due to inserting them too fast with a drill.

Scritto da: dan

Works great!

Works great in most situations. I use a smaller drill and an impact driver for installing the inserts when I need more strength. I’ve used there tool and inserts across a wide variety of woods from pine and cedar to mdf, osb, plywood, and in hardwoods like maple, ash, and oak.

Scritto da: Andrew Amatruda Jr.

Easy installed with the kit

The kit makes these inserts very easy to install properly

Scritto da: SF_Runner

You'll end up just using the inserts

I wanted to buy from an American shop but like someone else said previously, the drill bit it comes with is too large on softwoods. My project was made out of pine. I ended up having to buy a 5/16 drill bit as they suggested and it made a huge difference. I also ended up stripping one of the bits in a test piece with the installation bit they included trying to get it flush. To me this means the insert metal is pretty soft. You're better off just using an allen wrench and recess bit to have a clean install. This basically makes the other pieces in the kit useless and a waste of money and space in your shop.

Scritto da: RAT

Great Idea, didn't work out well for me.

I am building a slab desktop & I was using this product to set C-Channel into the bottom of the 2 slabs that make up the surface. I am using a relatively soft wood. The product comes with a 23/64" bit. After some testing on similar woods I found that diameter too large and only the top teeth really caught. For my softer wood application 5/16" worked best with the 1/4-20 inserts. The drill driver bit was a great idea, just not great for a softer wood. Too much torque available at speed. I found just using an Allen Wrench much more controllable. For my application, I'd have just been better off only buying the inserts (which I had to do anyway, not enough in the kit) - The inserts are a fantastic product!

Scritto da: Erin

Only for VERY soft woods

The inserts are tapered, and the top is larger than the the pilot bit. You can only use these in wood that is really soft. I split multiple pieces trying to get these to work. Using a 1/2” pilot bit helps. Would not use again.

Scritto da: Underdog

Herramienta y tuerca inserto para madera

Inslalar las tuercas inserto con esta herramienta fue muy sencillo y rápido, la broca hace un corte perfecto y la llace failita mucho porque lleva el in serto justo al tope.

Scritto da: Cliente de Amazon

Buen producto

Es un buen producto y lleno su función al utilizarlo