Momentive RTV103 Silicone, une partie, noir, cartouche de 300 ml

Brand:Momentive

3.9/5

53.17

Mastic silicone monocomposant à usage général qui durcit en un caoutchouc de silicone résistant, durable et résilient lorsqu'il est exposé à l'humidité atmosphérique à température ambiante. Produit de consistance pâteuse de résistance standard qui peut être appliqué sur des surfaces verticales et au-dessus de la tête où les scellants versables/autonivelants ne sont pas pratiques. Possède d'excellentes performances à basse et haute température -75° à 400°f. peut être utilisé dans les applications de contact alimentaire où les réglementations FDA s'appliquent référence : Cds4319. reconnu par UL sous le dossier UL e-36952.

Conforme aux spécifications militaires mil-a-46106 et nsf standard 51, est conforme fda 21 cfr 177.2600, est conforme usda et a des composants reconnus ul. La plage de service continu est de -75 à +400 degrés F (-60 à +204 degrés C) et la plage de service intermittent est de -75 à +500 degrés F (-60 à +260 degrés C). Adhère à de nombreux métaux, verre, céramique, caoutchouc de silicone et certains plastiques rigides sans utiliser d'apprêt. La consistance de la pâte permet une application sur des surfaces verticales ou aériennes. Mastic silicone rtv noir monocomposant avec une consistance de pâte pour remplir et sceller les espaces ou les fissures jusqu'à 1/4 de pouce.
Country of Origin USA
Item model number RTV103-300ML
Manufacturer Momentive
Package Dimensions 11 x 1.5 x 0.94 inches; 10.41 Ounces

3.9

8 Review
5 Star
83
4 Star
17
3 Star
0
2 Star
0
1 Star
0

Donnez votre avis

Votre courriel ne sera pas publié. Tous les champs obligatoires sont marqués d'un*

Scritto da: Wakawaka
Actual silicone is great, packaging no so much
So far I’m in for 7 tubes of this stuff and have had the same issue to varying degrees with all tubes. The plunger bypasses a ton of the silicone! Not only have I lost about 5-10$ worth of product every tube but my electric gun is a MESS. Yes I used a manual version too, and tried adding a fender washer to make sure I was supporting the entire plunger - same issue. I did cut my tips small and noticed that going slow reduced the loss but it shouldn’t be happening at all. Initially the directions fail to mention that you must puncture the inner seal after cutting tip. Not a big deal but threw me for a loop right off the bat because normally only cardboard adhesives have the seal and these tubes are plastic. Actual silicone is great quality, using it for fish tank stuff. I had success bonding acrylic to glass (over flow and sump building) and injecting it to reseal a stupid craigslist tank. One thing to note, if you’re using tape at the seam which you plan to remove while the silicone is still wet to get a clean line, you need to pull it off right after completing the seam. If you wait the typical 5 mins you’ll risk pulling the silicone OUT of the seam with the tape instead of just the excess that ran onto the tape.
Scritto da: ScottH
Sets up pretty quickly
It does grow a skin pretty quick, so you don't have heaps of time to get your bead looking the way you want. I found it stuck a little to the blue tape I was using as a mask. Not a big deal, but be prepared for it.
Scritto da: James daniels
This is what you want for fishtank's also, its black!
This is the best on the market for its application in fishtanks, its wayyyy better than silicone. Worth the expense. Just repaired a 3500 dollar fishtank i bought for 300 bucks with it.
Scritto da: I Buy Too Much
Works Like A Charm!
I chose this item due to the reviews regarding fish tanks. Had to reseal used bow front tank. Used frog tape to make perfect bead lines. Go slow by steady your caulk gun to get one continuous bead. Cut the caulk top to the size of bead you want to achieve. Do one pass with wet finger. Don't use a dry finger!!! Then do not touch it! Have wet paper towels ready as it can be messy. After drying I used a scraper to get off any random caulk. Do not scrap any part of aquarium side/bottom seal.If you made it messy, leave it. You do not want to break the cured seal. I waited until the vinegar smell was gone (about 40 hours as my tank was in garage) to rinse out and set up. Awesome product!
Scritto da: Brent Custer
Perfect
Caulking was perfect no hard spots. Great product and will buy again for sure
Scritto da: Bill
Used it to seal a 26 gallon tank worked excellent
Used it to seal a 26 gallon tank worked excellent
Scritto da: Tom Dehnert
Very strong aquarium safe
The best stuff period for redoing the inside of a fish tank
Scritto da: Mike jones
The best stuff around for Aquariums
Very strong, and very fast drying. Used it to repair damaged seals in a Waterbox rimless aquarium.

Produits connexes

Découvrez notre réseau international

Nous expédions dans 28 pays plus de 200 000 produits. Restez informé, inscrivez-vous à la newsletter.

Array