Motor Guard M-45-KIT Kit de filtre à air propre 1/4 NPT

Name: Motor Guard M-45-KIT Kit de filtre à air propre 1/4 NPT
Brand: Motor Guard
SKU: 012301866155
Price: 153.80 EUR
Availability: InStock

Brand:Motor Guard

3.7/5

€
153.80

Les filtres à air comprimé submicroniques Motor Guard sont la défense ultime contre l'air sale et nocif. Conçus pour être installés au point d'utilisation, ces filtres éliminent les particules, l'humidité condensée et les aérosols d'huile jusqu'à une taille incroyable de 0,01 micron. Aucun autre filtre sur le marché n'offre ce niveau de protection combiné à une faible perte de charge et une facilité d'utilisation. Fabriqué à partir de cellulose recyclée non blanchie, l'élément bobiné du filtre Motor Guard retient les contaminants et absorbe de grandes quantités d'humidité et d'huile. Le produit comprend un support de montage et du matériel pour une utilisation avec un tuyau de 1/4 de pouce. Cette unité se montera dans des cabines de pulvérisation, sur des découpeurs plasma ou sur d'autres équipements nécessitant de l'air ultra-propre et une connexion flexible.

Montant

Ajouter au panier Acheter maintenant

EAN: 012301866155

Catégories Automobile, Pièces de rechange, Filtres, Filtres à air & Accessoires, Filtres à air,

Fabriqué aux États-Unis. L'élément bobiné du filtre Motor Guard retient les contaminants et absorbe de grandes quantités d'humidité et d'huile. La pression maximale est de 125 psi, la plage de température est de 32 à 175 F et l'élément de remplacement est le m-723. La taille du port est de 1/4 NPT, le débit d'air nominal est de 45 CFM et la cote de filtration est de 0,01 micron. Contient un filtre Motor Guard modèle M-30, un support de montage, du matériel et 2 éléments de rechange.

Batteries Included?	‎No
Batteries Required?	‎No
Brand	Motor Guard
Color	‎Factory
Customer Reviews	4.7 4.7 out of 5 stars 128 ratings 4.7 out of 5 stars
Included Components	‎Motor Guard - Clean Air Filter Kit 1/4 Npt
Is Discontinued By Manufacturer	‎No
Item Dimensions LxWxH	12 x 5.5 x 10.75 inches
Item model number	‎M-45-KIT
Item Package Quantity	‎1
Item Weight	‎1.53 pounds
Manufacturer	‎Motor Guard
Material	‎Paper
Part Number	‎M-45-KIT
Power Source	‎Hand Powered
Product Dimensions	‎12 x 5.5 x 10.75 inches
Product Grade	Replacement Part
Size	‎One Size

5 Star

4 Star

3 Star

2 Star

1 Star

Donnez votre avis

Votre courriel ne sera pas publié. Tous les champs obligatoires sont marqués d'un^*

Votre note

Scritto da: D. J. M.

Works Great!

This was LOADS better than the cheap HF "Magician" 2 stage coalescent/dessicant filter it replaced. With only a compressor, aftercooler, regularor, booth filter, and gun regulator, the Magician in the booth was choking my paint gun making me crank up the line pressure to account for the pressure loss and the gun still didn't meet expectations. I was worried it was the long hose length (100ft 3/8" hose) as my paint booth is far away from the 60 gal compressor. The M-30 opened it right back up, allowing much better fan and fluid output without cranking the initial pressure up beyond 60 psi. The gun now sprays as it should with clean air, and no water! The kit is very economical with 3 filters included. Hookup was super easy & quick (10 minutes) with the bracket. If you're a DIY garage painter, this is a must-have!

Scritto da: Pat

Works very well

Works great good product for the money would buy again would recommend

Scritto da: Ronald J. Zembron

Great product

I owned one of these back in the early 80's and was constantly kidded about using a toilet paper roll for a filter. But I was painting Show Corvettes and found it to work perfectly. It's been years since I restored a Vette but I needed to do some minor body work and paint repair to a used Suburban I bought and needed a good filter system to use fro painting the panels. This filter immediately came to mind so I did some surfing and found that they still make it and have improved it since my last purchase almost 40 years ago. They now supply a great filter to use inside the unit that works extremely well. They are readily available and reasonably priced. They also eliminate the possibility of deterioration of the toilet paper roll that was possible if you didn't change the roll frequently. I only use mine with a dedicated air supply line to the filter and also a dedicated airline to the paint gun to eliminate the possibility of contamination when using air tools with oil. When using the air tools I remove the filter from the airline system by bypassing the filter and connecting my compressor after the filter system. I then connect to a oiler and dryer filter designed for such use with tools and separate air lines.

Scritto da: lr

FILTER

GREAT

Scritto da: cu

The Best Water / Moisture Trap .

I was having moisture in the compressor airline, entering my paint gun and ruining my paint job. I tried the so-called high-quality in-line water traps, but they all failed. As a true hero Motor Guard M-45-KIT 1/4 NPT Clean Air Filter Kit, solved this moisture problem. The result is clean dry air for spray painting. I have a plasma cutter so this kit will be ideal for dry h.p. air.

Scritto da: Mike Metzelfeld

Great air filter

I use this to filter air right before it enters my plasma cutter. There is an air dryer and filter up stream, I use this as the last line of defense before the plasma. This filter is a must have if you run a plasma cutter.

Scritto da: robert L

Air filter

Need to change the filter more often.

Scritto da: colormack

Great deal

Best price anywhere for a very simple but awesome air compressor filter

Scritto da: srblanch

Sturdy construction, efficient.

Sturdy construction, works great.