Prime-Line Products KC60HD Ressort de sécurité, 4-1/4 po, homologué UL, construction moulée sous pression, chrome satiné, ferme-porte sans main

Name: Prime-Line Products KC60HD Ressort de sécurité, 4-1/4 po, homologué UL, construction moulée sous pression, chrome satiné, ferme-porte sans main
Brand: PRIME-LINE
SKU: 7241870749849
Price: 45.69 EUR
Availability: InStock

Brand:PRIME-LINE

3.2/5

€
45.69

DESCRIPTION DU PRODUIT Ces ferme-portes de sécurité activés par ressort sont construits en matériaux moulés sous pression et sont livrés dans une finition chromée satinée. Ils sont U.L. répertorié avec une cote de résistance au feu de 1/2 heure et peut être utilisé pour fermer des portes pesant jusqu'à 150 lb. Ces ferme-portes disposent d'une vitesse de fermeture réglable et ils sont sans main, ce qui leur permet d'être utilisés sur des portes battantes à gauche et à droite. Le ferme-porte et la plaque coulissante en plastique sont montés en surface et sont faciles à installer. Ces ferme-portes fonctionnent selon une méthode de fermeture par poussée, plutôt que par une méthode de fermeture par traction, et ils n'ont pas de fonction de maintien en position ouverte. Distance de déplacement : le bras le plus proche de ce ressort de sécurité a la capacité de pivoter à 180 degrés, mais une fois monté en place, la distance de pivotement de la porte sera réduite au point où elle entre en contact avec la balle. boîtier en forme de ferme-porte. Pour une fermeture résistante à la rouille et aux intempéries, considérez les pièces Prime-Line KC50HD (blanc) et KC57US (marron) qui conviennent à une utilisation extérieure/extérieure, conçues pour être utilisées avec des portails légers et des portes moustiquaires. Toutes les fixations et les instructions d'installation sont incluses avec cet article. Les autres couleurs/finitions incluent : noir, blanc, marron et chromé. Assurez-vous de visionner la vidéo d'installation pratique du fabricant également liée à cette page, dans le coin supérieur gauche. L'application de graisse au lithium blanche sur les ressorts de compression internes peut être souhaitée, mais vous devez éviter d'utiliser des lubrifiants comme le WD-40 qui décompose la graisse lubrifiante. Ne pas trop serrer, tourner au-delà de 4 positions de trou entraînera l'échec de cet article. DU FABRICANT Ces ferme-portes de sécurité à ressort sont fabriqués en matériaux moulés sous pression et sont livrés dans une finition chromée satinée. Ils sont U.L. répertorié avec une cote de résistance au feu de 1/2 heure et peut être utilisé pour fermer des portes pesant jusqu'à 150 lb. Ces ferme-portes disposent d'une vitesse de fermeture réglable et ils sont sans main, ce qui leur permet d'être utilisés sur des portes battantes à gauche et à droite. Le ferme-porte et la plaque coulissante en plastique sont montés en surface et sont faciles à installer. Ces ferme-portes fonctionnent selon une méthode de fermeture par poussée, plutôt que par une méthode de fermeture par traction, et ils n'ont pas de fonction de maintien en position ouverte. Distance de déplacement : le bras le plus proche de ce ressort de sécurité a la capacité de pivoter à 180 degrés, mais une fois monté en place, la distance de pivotement de la porte sera réduite au point où elle entre en contact avec la balle. boîtier en forme de ferme-porte. Pour une fermeture résistante à la rouille et aux intempéries, considérez les numéros de modèle KC50HD (blanc) et KC57US (marron) qui conviennent à une utilisation extérieure/extérieure, conçus pour être utilisés avec des portails légers et des portes moustiquaires. Toutes les fixations et les instructions d'installation sont incluses avec cet article. Les autres couleurs/finitions incluent : noir, blanc, marron et chromé. Assurez-vous de visionner la vidéo d'installation du fabricant également liée à cette page, dans le coin supérieur gauche. L'application de graisse au lithium blanche sur les ressorts de compression internes peut être souhaitée, mais vous devez éviter d'utiliser des lubrifiants comme le WD-40 qui décompose la graisse lubrifiante.

Montant

Ajouter au panier Acheter maintenant

EAN: 7241870749849

Catégories Outils et amélioration de la maison, Quincaillerie, Immobilier de porte et serrures, Ferrures de portes,

Pour plus d'informations sur les dimensions, veuillez consulter le dessin au trait. Conception de montage en surface compacte et durable. U.L. classé et classé au feu pendant 1/2 heure. Informations sur le produit – Ce ferme-porte à ressort de sécurité dispose d'un design sans main et d'une finition peinte en chrome satiné pour compléter n'importe quel style de porte. Base de 1" de large, espacement des trous de 4-1/4" et bras de 4-3/4". TENSION RÉGLABLE - Réglez facilement la tension sur ce ferme-porte à ressort de sécurité. Ces ferme-portes disposent également d'une vitesse de fermeture réglable. INSTALLATION FACILE - Avec un ferme-porte et une plaque coulissante en plastique montés en surface, l'installation est un jeu d'enfant. Ce ferme-porte à ressort peut être utilisé sur des portes jusqu'à 150 lb et peut être utilisé sur des portes à gauche et à droite. PROJET DE BRICOLAGE FACILE - Grâce à ces ferme-portes à ressort de sécurité KC60HD, votre prochaine tâche est rapide et facile. Utilisez ces ferme-portes pour convertir des portes battantes en portes à fermeture automatique. Comprend – (1) ferme-porte à ressort monté en surface, tige de tension, plaque coulissante et bouchons pour couvrir les trous de réglage dans le corps du ferme-porte après avoir réglé la tension souhaitée ; fonctionne sur des portes jusqu'à 150 lb; sans main ; tension réglable; U.L. listé ; Coupe-feu 1/2 heure.

Batteries Included?	‎No
Batteries Required?	‎No
Brand	PRIME-LINE
Certification	‎UL, ADA
Color	Satin Chrome
Color	‎Satin Chrome
Country of Origin	‎China
Customer Reviews	4.1 4.1 out of 5 stars 264 ratings 4.1 out of 5 stars
Domestic Shipping	Item can be shipped within U.S.
Exterior Finish	Chrome
Finish	‎Chrome
Included Components	‎Door closer, winding rod and fasteners
Installation Method	‎Screw In
International Shipping	This item can be shipped to select countries outside of the U.S. Learn More
Is Discontinued By Manufacturer	‎No
Item Dimensions LxWxH	4.75 x 1.25 x 3.75 inches
Item model number	‎KC60HD
Item Package Quantity	‎1
Item Weight	‎14 ounces
Manufacturer	‎Prime-Line Products
Material	Diecast
Material	‎Diecast
Measurement System	‎Inch
Mounting Type	‎Surface
Part Number	‎KC60HD
Product Dimensions	‎4.75 x 1.25 x 3.75 inches
Size	‎4-1/4 in.
Style	‎Safety Spring
Warranty Description	‎Goods are warranted against manufacturing defects for 1 year. In no case is Prime-Line responsible for user related damage or damage incurred during installation. Warranty is void if products are subjected to abnormal conditions, misapplication or abuse.

5 Star

4 Star

3 Star

2 Star

1 Star

Donnez votre avis

Votre courriel ne sera pas publié. Tous les champs obligatoires sont marqués d'un^*

Votre note

Scritto da: The BIM Artisan

A very good closer for the money, just beware of your materials & needs. It won't work for ANY kind of door but will for most.

I bought the Satin Chrome door closer Jan 6th & had it installed in about 20 minutes on a door roughly 90-110 lbs on ball bearing hinges mounted to a metal door frame. Because the Hinges are ball bearing, the door closes really easily. Being a heavy door with glass, I had my reservations as this doesn't actually control the door closing, it simply pushes the door closed. The closer comes with a 5" closer rod, the closer spring housed in a cylindrical mount, a rod guide, a spring tension bar (about 1-1/4"), some hole caps, & (4) wood screws about 1" long. Upon mounting the closer, I marked the area I wanted the closer on a metal frame & began drilling a pilot hole. My drill bits are designed for metal but this is a heavy gauge steel frame & after about 40 seconds of drilling I realized I needed some oil to continue so I checked my progress and discovered I'd barely made a dent. I suppose if you have the patience & oil to drill metal this will work on a heavy gauge steel door frame but I had neither, so I improvised. I'm glad the rod is as long as it is & wish it was a little longer as I mounted the closer directly aft the steel door frame. With the door frame about 1-1/2" wide, I lost about 1-3/4" of rod to the door so the closer will have to work harder with less leverage. With the door on ball bearing hinges I was hoping this would compensate for the speed of the closing of the door, I didn't need a lot. I drilled the hole for the screws smaller than the diameter of the screws in hopes of having some good bite for the screws as these screws were going into steel studs, not wood. Please realize, for every action there is an opposite & equal reaction. There are some pics from previous posts showing the spring housing tearing out of the wall or tearing the wood frame from the wall. As much force as you are using to close the door, there is an equal amount of force on the screws trying to pull or torque the spring housing from the wall or door frame. You need a good bite on the screws & preferably twice as deep as the sheet rock wall or wood frame. Most manufacturers selling items such as this door closer provide the minimum required size of screw & many times these screws fail to get adequate bite. It is advisable to stop by the nearest Home Depot & pick up some deeper screws before mounting this door closer. You want the screws biting into the wood or steel stud, not just the door frame or sheet rock. Especially if you have to torque this closer a few times. After mounting the spring housing, I added the closer rod briefly to the spring just to find where the guide would sit & marked it. Then removing the closing rod I mounted the guide onto the door. The door closer has (4) holes for the closer rod, each at 90 degrees. Putting the tension bar in the hole perpendicular to the wall, I tensioned the closer & added the closer rod parallel to the wall & within the guide. Then removed the tension bar & tested the door closer. All I needed was a little push & the weight of the door would do the rest so a quarter tension on the closer worked beautifully ... for about a week. There is a break-in period with any given spring (especially torque springs) & this one goes about a week with mid to heavy traffic through the door. After the first week the door closer was not pushing the door near as much as when I first installed it, thus the door would not close completely. Adding another quarter tension to the door actually pushes the door a little too much & the door now slams shut. Not enough to break the glass but enough that I am uncomfortable with it. NOTE TO MANUFACTURER: It would be nice if there were (5) holes evenly spaced around the spring instead of just the (4) holes at 90 degrees. Tension could then be adjusted a bit easier for the user & the user could determine or control a little better how much tension to put on the spring / door. As noted in other reviews, there's a noise associated with this spring closer. Pick up some Lithium grease or other good quality lubricant when you pick up your screws (the instructions suggest NOT using WD-40) & you'll be golden for quite some time. If you are using this on standard pin hinges, you can use the grease or lubricant on the spring closer & your pin hinges of the door to reduce the friction of the hinge for a smooth closing action. [Update 11.03.2017] - This closer is still working as it should. Haven't adjusted it since the last posted adjustment a week after installation, almost a year ago. I highly recommend this, especially on ball bearing hinges. I'm thinking this will last for quite a few years.

Scritto da: David

Works well enough given the price - could be better.

This spring-loaded door closer certainly does the job - but not without some caveats. Installation: It's not clear from the pictures, but there are 4 pieces when you open the package. The spring closer body, the push bar, a shoe for the push bar, and a tensioner bar used to rotate the center ring. The push bar screws into one of the 4 sockets on the closer body - you choose which one by using the tensioner bar to pre-tension the internal springs and then selecting the appropriate socket. It's difficult to explain - maybe I'll do a video later. The shoe provides some protection to the door from the push bar rubbing against it when it does its job. The closer body screwed into the wall or door frame - wood screws are provided. Functionality: Yes, this setup is adjustable tension - but it is not infinitely adjustable. There are set amounts of force you can set for the door closer. If you don't like the preset tensions - too bad. It's either going to close too hard or not hard enough. Build quality: This is the same asPrime-Line Products KC10HD Safety Spring Door Closer, White except in satin chrome. It reminds me of galvanized steel - like it's made of the same material as chain link fences. It feels like it's solid metal - not a lot of worry about the device breaking. I'm not so sure that some door frames are going to be up to the amount of force this will put on the frame and molding. Only time will tell. Noise: This was my biggest disappointment. I had read about noise complaints in other reviews, but figured - how bad could it be? When I first installed it, I learned it can be really bad. The device had a loud grating sound - analogous to someone opening a garage door. Other reviews mentioned grease; so I tried dripping teflon lubricant into the body and moving/shaking parts to try to coat whatever was inside. This had hardly any affect, so I took the nuclear option. I took the one screw that holds the whole thing together, and I discovered that there was a rusty spring inside that was rubbing on itself every time the door closer moved. So I coated _everything_ inside with some white lithium grease and re-assembled it. This solved the problem - quiet as can be now. I wish the manufacturer would spend an additional $0.50 to improve this detail and this could easily by a 5-star review.

Scritto da: M Hale

Nice small size, but didn't work well for my fire door

I purchased this for fire door between my house and garage. By code, you need a self-closing mechanism on a door like this and I didn't want anything to big and industrial looking, and thought this would be perfect. It did seem to work well at first, but I really needed to crank up the tension to get the door to latch consistently - so much so that the small tensioning bar that came with it was not enough, so I used a long machine screw instead. Think the torqueing was too much for this little guy and one day I hard something snap, and it no longer latched the door, plus it caused the molding around the door to separate. Think this would work very well for a different kind of interior door, but the seals around a fire door require too much extra "oomph" to close.

Scritto da: Francis J. Pirozzi

Super

I installed this on my gate for my pool ladder because the one that came with the ladder broke. This one works like a champ super value

Scritto da: L

Slim design better than bulky, expensive door closer

Very good option for a door that needs to close, but a bulky door closer would not fit. Easy to adjust. The only con is the open nature of the design “sprays” some kind of mechanical “dust” on the door from the rod moving back and forth (see pic).

Scritto da: Tj Naylor

Works great

Definitely works for what i bought it for. The only problem i had is the spring is loud

Scritto da: Philip C Marcello

Very effective

It does what I needed it to do, keep my bedroom door shut. I house share and the other house member has a dog. I don't want his dog going in my bedroom and once in a while I would forget to shut the door and find the dog in their. This gadget solved my problem. I gave it a four and not a 5 because it does make a noise. Not loud or terrible, but late at night, it might be audible.

Scritto da: Gabriela Carrillo

No me funciono

Lo necesitaba para una puerta de metal y aún que le puse 2 no logro cerrar por completo la puerta, supongo que solo funciona en puertas de madera o puertas más ligeras.

Scritto da: Amazon Customer

Easy to install

Purchased two installed vary easily, as of now they are performing well. Cheers Bob McCabe

Scritto da: Allison D.

Excellent product!

This product is just perfect! Easy to install and not noticeable! We used it on our pantry door and now the door always stays closed,, gently!

Scritto da: Cathy

Four Stars

These work really well but they do make a noise when the door closes

Scritto da: Ace

As Advertised

Easy to install. Worked as advertised.