Scellant de fuite de bateau en aluminium TotalBoat

Name: Scellant de fuite de bateau en aluminium TotalBoat
Brand: TotalBoat
SKU: 0811932022776
Price: 68.88 EUR
Availability: InStock

Brand:TotalBoat

3.3/5

€
68.88

Les bateaux en aluminium mènent une vie difficile. Ils s'échouent, frappent des objets immergés dans l'eau et ont tendance à être utilisés pendant de nombreuses années. Au fil du temps, les rivets et les coutures développent des fuites, des fissures ou même des trous. Un bateau en aluminium qui fuit peut couler rapidement. La plupart des produits de réparation existants sont fastidieux et chronophages. Leurs instructions vous obligent à enduire le dessous du bateau. Ils ne supportent pas bien la flexion ou le stress, ce qui entraîne des fissures et un échec de la réparation. TotalBoat Aluminium Boat Leak Sealer est différent. C'est le moyen rapide et facile de réparer les rivets, les fissures, les coutures et les trous qui fuient dans votre bateau en aluminium. Il est livré dans une cartouche pratique qui s'adapte à un pistolet à calfeutrer standard. Insérez simplement la cartouche dans le pistolet, fixez l'embout mélangeur inclus à la cartouche, pointez, tirez sur la poignée et jetez les 3 à 4 premiers pouces de cordon. Après cela, Leak Sealer sort mélangé au rapport exact 1: 1 afin que vous obteniez un durcissement approprié et un joint étanche. C'est aussi simple d'obtenir le bon mélange et un traitement fiable à chaque fois. Si vous vivez dans un climat plus froid, vous apprécierez le fait que vous n'avez pas à attendre que le temps se réchauffe, vous pouvez appliquer Aluminium Boat Leak. Scellant lorsque la surface en aluminium et la température de l'air ambiant sont aussi basses que 40 °F, tant que la surface en aluminium a été préparée correctement. Le scellant de fuite de bateau en aluminium est résistant à l'affaissement, il reste donc là où vous le mettez et ne coule pas des coutures et des trous. Le temps de gel est de 40 minutes à 72°F. La résistance à la flexion est de 8 800 psi. La résistance à la compression est de 7 200 psi. Peignez sur les réparations durcies pour une protection maximale. Attendez 7 à 10 heures avant de poncer et de peindre. Attendez 24 heures avant de soumettre l'époxy durci à des charges élevées. Comparé au kit de réparation de bateau en aluminium West System G/Flex 650-K. Avec TotalBoat, il n'y a pas de mesure, pas de mélange, pas de gâchis et presque pas de nettoyage. Tous les produits TotalBoat sont développés par des plaisanciers pour des plaisanciers, pour offrir une grande valeur et d'excellents résultats. Nous savons ce qui fonctionne et ce qui ne fonctionne pas.

Montant

Ajouter au panier Acheter maintenant

EAN: 0811932022776

Catégories Industriel et scientifique, Sports et plein air, Sports et Fitness, Navigation et voile, Bateaux et équipement, Fournitures d'entretien, Fournitures de peinture,

Disponible dans un format pratique de 250 ml. cartouche qui s'adapte facilement aux pistolets à calfeutrer standard. Comprend 2 embouts mélangeurs statiques. La résine et le durcisseur sont livrés dans une seule cartouche et sont distribués automatiquement au bon rapport. Pas de mélange. Pas de gâchis à nettoyer. Peut être appliqué sur des surfaces en aluminium correctement préparées lorsque la température de l'air et du substrat est aussi basse que 40 °F. Un long temps de travail (75 minutes @ 72°F) assure une meilleure pénétration et une meilleure étanchéité. Absorbe les contraintes de contraction, de vibration, de choc et d'expansion en tenant fermement pour éviter les fuites. Le scellant époxy facile à utiliser, en deux parties, flexible et imperméable répare les rivets et les coutures qui fuient et colmate rapidement et efficacement les petits trous sur les bateaux en aluminium.

Brand	TotalBoat
Color	Buff
Compatible Material	Aluminum
Is Discontinued By Manufacturer	No
Item model number	497724
Manufacturer	TotalBoat
Material	Resin
Package Dimensions	9.92 x 2.87 x 1.93 inches; 13.76 Ounces
Style	Compact

5 Star

4 Star

3 Star

2 Star

1 Star

Donnez votre avis

Votre courriel ne sera pas publié. Tous les champs obligatoires sont marqués d'un^*

Votre note

Scritto da: Kindle Customer

Easier to apply than other ratings implied

I bought this product to seal loose rivet leaks in my aluminum boat. I have not put the boat on the water yet, so cannot comment on how well it worked. That's why I gave it four stars and not five. I gave it four because the product was delivered promptly including a card asking for comments and offering a 20% coupon for future purchase as well as a product support phone number. Very nice service offer that at least appears as if the company - TotalBoat - is concerned about customer satisfaction. The product came well packaged and included two dispenser tips and a container that fits any caulk gun. Other comment had me a bit worried about being able to dispense the epoxy because I don't have great hand strength, however, cautioned by instructions on the tube I laid it in front of a heat duct while I prepared the surface and then had no trouble dispensing it at all. It was easy to get out of the tube, emerged as a not overly thick and easily pliable liquid that was very easy to manipulate, and ultimately made a nice layer that looks like a good seal. I applied it to rivets in the boat's floor then again on the bottom (so overhead). It stuck and stayed well in both locations. I've used Gluvit before and been very happy with it's property of filling in along the shaft of rivets as well as over the ends. This product is a little thicker, but it also had some flow so I'm hoping, but can't say for sure, that it did the same. In a week or two after I've finished this repair and installed the new floor, I will put the boat and the water. If it works as I hope, I'll change the rating to five stars. If not - well, you may see a new message in this space, but from all appearances I expect it to perform well.

Scritto da: Amazon Customer

Not mixing

I’m sealing the rivets on an aluminum Jon boat, the package states first 3-4 inches will be waste until mixed. I wasted first 5” just to be sure. For the next 40 rivets it seemed to work fine, then half way through it changed colors and I was only getting the orange/brown color assuming this is just hardener. So half my boat rivets got the epoxy side and the other half got just the hardener. Not happy with how it turned out because the first half I had to wipe off because there was no hardener. In the future I would buy a pre mixed boat epoxy from Home Depot.

Scritto da: Amazon Customer

Great product

I used this to seal some leaky rivets on a jon boat I recently acquired. Using a cheap caulk gun and the provided tips, it worked very well. It can be a little temperature sensitive so make sure you apply in conditions above 60 degrees. I did some application at that temperature and really killed my hand trying to squeeze the caulk gun trigger. I finished the job a few days later in warmer weather and found the application to be so much easier. The only thing to be aware of is that the tube can be a little misleading in size. It's only about 1/2 full, but I was able to seal every rivet on the bottom of my 14 boat, half the rivets on the inside, and several of the seams. It is however a caramel colored product and won't dry clear, so it will stand out that you've used it. That being said, it was perfect for my needs.

Scritto da: Real Customer

It seems to work

It takes more than 3 inches of material before it is properly mixed. Wait for the color to change to brown before applying it. It was white after 4 inches so I used it as it changed color. That section did not harden.

Scritto da: Jonathan Cowal

So far this has been a great product. I used it to seal every rivet ...

So far this has been a great product. I used it to seal every rivet and seam on an aluminum boat I was fixing. Some people have complained that it was difficult to dispense but I purchased the cheapest caulk gun I could find and it wasn't too bad. It was very easy to work with, I used a putty knife and was able to shape it easily around the areas I was working on. Also, it really does stay exactly where you apply it even when working on slanted or even upside down surfaces. Once sanded, I was able to paint over it and you cannot tell that there is anything there. I give it 4 stars because I have yet to test the boat out and I do not know how it holds up over time.

Scritto da: Kevin Vail

Very easy to use

I bought this to pro-actively seal the non-welded ribs on the hull of my 14ft v-hull. The mixing tip worked great. Each stick comes with two mixing tips in case you don’t use all of the compound in one instance. The compound is very easy to work with and apply and dries pretty quick for sanding and painting. So far I would highly recommend any product from this company.

Scritto da: MattG

Sealed up leaky aluminum boat

Worked well. I used it to seal a leaky riveted seam where the bottom of my aluminum boat meets the transom. Followed the instructions regarding surface prep, no problem squeezing it out with a standard cheapie caulking gun. Came out thin enough for me to force it into and through the seam with some compressed air, then gave it a thicker bead inside and out, then had plenty of time to smooth it. Took paint well. The following week, took it out to the lake, it sat in the water for 6 days with an hour or so of driving around each day, and no leaks at all. Very satisfied.

Scritto da: Barbara Bing

Takes some experience to apply

Did a good Job on leaks to an aluminum boat. Stuff is quite viscous and ease of application depends on size of opening. Used calking gun. Two nozzles to try with - you get better with time.