0
0

Total:€ 0.00

Voir le panierVérifier
LoginRegister
0

Total:€ 0.00

Voir le panierVérifier
LoginRegister

Yost Vises 908-HV Étau combiné tout acier

Brand:Yost Vises

3.7/5

€
508.83

Cet étau est aussi robuste que possible, construit en acier coulé structurel. Parfait pour vos projets de serrage légers ou lourds sur du bois ou des tuyaux. Cet outil tout en acier est doté d'une base pivotante complète et de verrouillages. Cet étau haute visibilité est conforme à la spécification OSHA 1910.144 -- Normes de couleur de sécurité. Yost Vises produit des étaux et des accessoires d'étau de haute qualité depuis 1908. Nous fournissons nos produits aux grands distributeurs et aux artisans individuels du monde entier, allant des étaux de qualité industrielle, des étaux de qualité professionnelle, des étaux de qualité atelier, légers à lourds. étaux de service, étaux multifonctions, étaux de soudage, etc. Nos produits respectent ou dépassent la norme industrielle de la spécification fédérale GGG-V-410A, offrant aux consommateurs des produits de qualité qui durent des années à un prix avantageux.

Montant
Ajouter au panierAcheter maintenant

EAN: 0797734008135

Catégories Outils et amélioration de la maison, Industriel et scientifique, Sets de batteries et chargeurs, Maintien au travail, Outils à main, Vis, Étaux d'établi,

GARANTIE : Livré avec une garantie limitée de 5 ans et un retour de 90 jours. INFORMATIONS DE SÉCURITÉ : Une mauvaise utilisation des étaux peut causer de graves blessures aux yeux, aux mains et/ou à d'autres parties du corps. Les étaux doivent être installés et utilisés correctement. Avant l'installation et l'utilisation, lisez, comprenez et suivez toutes les instructions décrites dans le manuel. Qualité Yost Vises : chaque outil Yost Vises est conçu pour avoir des normes élevées de qualité, de résistance et de durabilité. Nous privilégions la qualité à la quantité et fabriquons des produits sûrs et faciles à utiliser. Nous offrons un support technique à vie pour soutenir notre garantie de qualité. MODE D'EMPLOI : Assurez-vous que l'étau est solidement fixé à l'établi et que le verrou de la base pivotante est sécurisé. Ouvrez l'étau en tournant la poignée de l'étau dans le sens antihoraire. Placez l'article entre les mâchoires dentelées. Fermez l'étau en tournant la poignée de l'étau dans le sens des aiguilles d'une montre jusqu'à ce que l'article soit bien ajusté dans les mâchoires dentelées, continuez à serrer jusqu'à ce que vous ne puissiez plus déplacer l'article. Ne serrez pas trop car cela pourrait endommager l'article et/ou l'étau. Lorsque vous avez terminé de travailler sur l'article, tournez la poignée à vis dans le sens antihoraire pour libérer l'article. BASE PIVOTANTE : Base pivotante complète à 360 degrés avec 2 verrouillages. SPÉCIFICATIONS TECHNIQUES : largeur de la mâchoire 8 (20,32 cm), ouverture de la mâchoire 8 (20,32 cm), profondeur de la gorge 3,5 (8,89 cm), capacité minimale du tuyau 0,75 (1,905 cm), capacité maximale du tuyau 2,25 (5,715 cm). ÉTAU COMBINÉ : L'étau de tuyau et d'établi Yost Vises 908-HV 8 pouces est fabriqué à partir d'acier coulé structurel (SC37). Équipé de mâchoires de tuyau permanentes et d'une grande enclume renforcée. Il a une poignée de vis principale sans pincement.
Brand Yost Vises
Color Yellow
Country of Origin China
Item Dimensions LxWxH 10 x 10 inches
Item model number 908-HV
Item Weight 20 Kilograms
Manufacturer Yost Vises
Material Alloy Steel
Style High-Visibility Heavy Duty

3.7

13 Review
5 Star
74
4 Star
17
3 Star
6
2 Star
2
1 Star
1

Donnez votre avis

Votre courriel ne sera pas publié. Tous les champs obligatoires sont marqués d'un*

Scritto da: Nor
Seems like great product
Haven’t used yet. But, was impressed with the sturdiness.
Scritto da: Happy Shopper
Nice craftsman vise
To be clear I have not placed a bar or pipe in this vise and beat on it with a hammed to shape it. If you use one that way my review will not help. That said I really like this compact well designed vise. One point of the design that stands heads and shoulders above the comp, is that the base allows the vise to swivel 360 degrees. Hoodog! If you want to utilize your vise fully on a small work bench you need to be able to swing to either or both sides, so 360 degrees is important. It grips very well, sturdy so steady, finally the swivel lock is two, count 'em two, levers so one is on each side. I love that feature. I mounted this on a pre-built workbench that is 4 ft long and the size is a great match. You would not want anything larger. I did find, as are most new vises, that there was some dirty grease that needed wiping off and the main spindle threads were dry. I lubed up the threads it is smooth as silk. Do this, it will improve your overall experience. Being 66 yrs old I doubt I will be buying more in the future, but you should. Money well spent.
Scritto da: Wolfman
Sturdy with Harbor Freight fit and finish
This vise is a real mixed bag - better than I feared but worse than I'd hoped, particularly with the Yost name attached. First off I'm not a pro, just a homeowner tired of "homeowner grade" tools that break. My first thought for a vise was to get a used one, but my area has a truly dire selection at this price point. After months of looking I decided to take a chance on something new. The good: this vise certainly seems sturdy. It's honestly overkill for me. My primary concern with this purchase was getting something that won't break. The world is rife with reports of cheap cast iron vises with casting voids or impurities that snap in half when you need them most. My hope with this vise was that the material (cast steel) and heft would prevent that. In person it does inspire confidence, although I haven't tested it's limits. The jaws on my example line up, which was a fear based on some reviews. Once clamped down, it holds fast and hard. The bad: fit and finish. So far removed from the online shots it's almost a different product. Absolutely none of the surfaces are what I would consider "machined". More like gone over once with a 40 grit grinder. There's burrs everywhere. The crinkle coat on my example had a couple of spots that got missed or rubbed off in transit. And the slop! There is slop simply everywhere slop could be. The main screw's retention pin is off by a mile, giving the handle slop. It wobbles and waggles when adjusting, because the fitment of the bar in the body is approximate at best (with no means of adjustment). The main screw binds up at 90% extension for reasons I can't quite diagnose. I took it apart and did my best to clean it up, but most of the issues are simply cast in. Honestly it's on par with stuff I've bought from Harbor Freight in terms of fit and finish. I guess you get what you pay for with this one, and not a penny more
Scritto da: D Stone
Not as beefy as I anticipated, but the fit and finish are both very good.
This is a general purpose vise for my garage and it appears to be a good value. The size of the jaw opening for the price is better than many alternatives. I like the idea of steel vs. gray iron from a strength basis particularly in shock loading like hammering on a piece clamped in the jaws. Gray iron is strong, but does not understand flexing or bending - it behaves more like glass in these conditions; it is very tough right up until the time it shatters. The ideal solution would be ductile iron, but confirming they actually supplied ductile vs gray iron is a job for a test lab and not worth the effort or risk. Some people complained the Yost name was not on the vice, but I really don't care if it is or is not - no impact on function.
Scritto da: gabriel james hornbrook
Good vise (i bought it on sale)
I bought this cuz it was on sale for like 53 dollars. I’m very happy with it. It’s great quality
Scritto da: J. P. Vossen
Anvil part is too soft
So far this is very solid, but the anvil part shows marks and I can feel small indentations with my finger. I didn't expect that and didn't have that on my old cast iron vise I could pound on anything on my old Littlestown No 150 vise's anvil all day long and it shrugged it off, but not this one. Unfortunately the 150's jaws snapped off in the cold.
Scritto da: Dave
Its Purdy & Sturdy.
It has room for 5/8 inch bolts, so you can seriously lock it down, I've put some pretty heavy demands on it without any loosening or anything even taxing its abilities, simply put if you need a solid vise, this is the one. I like the yellow high visibility color, it looks good in the shop.
Scritto da: Mr. Bill
Yost makes good vises.
I am a professional fine woodworker, and vices are important in my work. I've therefore researched them extensively, and am always lead to Yost, never disappointed by them. The price point is good, but that means nothing if the thing does not work. Yost provides both a fair price and strong function.
Scritto da: Colin Noon
Use caution. " Utility "
Do not confuse this vise with a Wilton or Record both of which may cost $100 more . When mounted to bench as close as possible to the front edge, the back jaws are behind the the front edge of bench. making vertical securing of any piece longer than the height of the vise difficult at best. The description quote " Utility " can obviously have more than one interpretation. Cn.
Scritto da: Jonathon M.
Would Recommend
all I can say is as a farmer I bought the 6" vice to replace one that I broke on the farm, and after using this vice a few times now, I would recommend it, id also say that ill probably be getting another one one as well for my shop.
Scritto da: Darrell
Great vise
This is a great vise. It is cast steel and costs significantly more than a similar cast iron vise. It supposedly is stronger, but who knows... It works perfectly.
Scritto da: Alfredo
Resistente y buen tamaño
Buen producto, realmente es de acero llevo 4 meses con el y aún sigue sin óxido y es muy resistente.
Scritto da: Serry
Five Stars
Perfect!

Produits connexes

hot
Wilton CS6, étau de perceuse à 6 glissières croisées, ouverture de mâchoire de 15,2 cm, profondeur de mâchoire de 5,1 cm (11696) Étau d'établi
3.2/5

€ 783.17

Wilton CS6, étau de perceuse à 6 glissières croisées, ouverture de mâchoire de 15,2 cm, profondeur de mâchoire de 5,1 cm (11696) Étau d'établi
3.2/5

€ 783.17

hot
Étau pour perceuse à colonne Palmgren, 2 7/16 po W, ouvert 2,5 D, gris
3.8/5

€ 172.84

Étau pour perceuse à colonne Palmgren, 2 7/16 po W, ouvert 2,5 D, gris
3.8/5

€ 172.84

hot
WEN VJT606 Lot de deux coussinets magnétiques universels à prise souple 15,2 cm
3.5/5

€ 37.84

WEN VJT606 Lot de deux coussinets magnétiques universels à prise souple 15,2 cm
3.5/5

€ 37.84

hot
Yost Vises BC-6 Banc Chaîne Étau
3.7/5

€ 230.04

Yost Vises BC-6 Banc Chaîne Étau
3.7/5

€ 230.04

hot
HHIP 3900-0251 Étau de précision pour outilleur, 3 mâchoires de largeur x 1,375 de profondeur, ouverture à 4 mâchoires (lot de 1) 3 mâchoires de largeur
3.6/5

€ 373.78

HHIP 3900-0251 Étau de précision pour outilleur, 3 mâchoires de largeur x 1,375 de profondeur, ouverture à 4 mâchoires (lot de 1) 3 mâchoires de largeur
3.6/5

€ 373.78

hot
Wilton 865M Mechanics Pro Étau de banc, largeur de mâchoire 6-1/2, ouverture 6 mâchoires, gorge 4-3/8 (28812)
3.6/5

€ 1070.41

Wilton 865M Mechanics Pro Étau de banc, largeur de mâchoire 6-1/2, ouverture 6 mâchoires, gorge 4-3/8 (28812)
3.6/5

€ 1070.41

hot
Yost Tools Vises 250 Étau de banc à pince 2,5 Bleu
2.9/5

€ 89.64

Yost Tools Vises 250 Étau de banc à pince 2,5 Bleu
2.9/5

€ 89.64

hot
Yost Étaux 455 Étau combiné
3.8/5

€ 228.90

Yost Étaux 455 Étau combiné
3.8/5

€ 228.90

Découvrez notre réseau international

Nous expédions dans 28 pays plus de 200 000 produits. Restez informé, inscrivez-vous à la newsletter.

Array

Total:€ 0.00

Voir le panierVérifier

Catégories

Toutes les catégories
Menu Catégories Près Chariot

Menu