Milton S-698 1/4 FNPT Single Head Air Chuck mat Grip

Brand:‎Milton

3.8/5

36.78

Made in USA. Net fir mat Inflator Jauge ze benotzen. Maximum Loftdrock vun 150 Pond pro Metercarré Zoll. 1/4 weiblech national Päif thread.

Made in USA. Net fir mat Inflator Jauge ze benotzen. Maximum Loftdrock vun 150 Pond pro Metercarré Zoll. 1/4 weiblech national Päif thread.
Brand ‎Milton
Country of Origin ‎USA
Customer Reviews 4.7 4.7 out of 5 stars 434 ratings 4.7 out of 5 stars
Domestic Shipping Item can be shipped within U.S.
International Shipping This item can be shipped to select countries outside of the U.S. Learn More
Is Discontinued By Manufacturer ‎No
Item model number ‎S-698
Item Weight ‎3.2 ounces
Manufacturer ‎Milton Industries
Manufacturer Part Number ‎S-698
Model ‎s-698
Product Dimensions ‎4 x 1 x 5 inches
Special Features ‎1/4" female national pipe thread- Maximum air pressure of 150 pounds per square inch- Not for use with inflator gauge- - - - - -

3.8

8 Review
5 Star
83
4 Star
10
3 Star
4
2 Star
1
1 Star
2

Schreift Är Bewäertung

Är E-Mail gëtt net publizéiert. All obligatoresch Felder sinn markéiert mat*

Scritto da: Jeff Santo
Best value for the money!
The build quality is very good and has a solid seal against the tire valve stem. I bought two of these and set them using a piece of threaded brass pipe between the chuck and air fitting. This just makes it a little easier to grab ahold, there is no flex like there would be as if it were directly connected to the hose.
Scritto da: Amazon Customer
Works great !
Hold tight , doesnt leak.
Scritto da: Gingg
Locks on securly
Good quality, they lock on good and tight at 150psi. I use these for airing up after wheeling in the rocks.
Scritto da: Jeepin’
Awesome Clip On Air Chuck
Can’t go wrong with Milton brand. Great quality, holds on the stem well, so you don’t have to sit there and hold it on. Much better quality and holding power than the one it replaced.
Scritto da: dwayne tillotson
Works great
I don't have the strength in my hands that I used to have so very impressed with how well this works. Once it is connected there is no air leakage
Scritto da: jb
Just what I needed
Had to replace the air chuck on my small portable compressor and needed one that would lock on the stem and not come off like my old one. This fit the bill and works great. I added a brass hose barb and installed it to the original air line on my compressor. It works great and makes life so much easier.
Scritto da: Matt Rentz
Bad design
OK, it works........as long as you can get access to the valve to lock it on. The locking lever is long and large and sticks out at 45 degrees which makes it a challenge to install on a valve stem tucked in close to the wheel. I've seen other designs where the locking lever is much small and rides alongside the shaft; not sticking out and requiring so much clearance to use. I'm not sending it back but I took it off and put the old (non-locking) fill nozzle back on. Tired of fighting with my Ford F150 wheels to use it.
Scritto da: Ken
Started leaking after a few uses.
Wont stay on the valve stem. The locking lever ill not hold it.

Zesummenhang Produiten

hot
RPB C40 Klima Kontroll Apparat
0.1/5

€ 672.13

RPB C40 Klima Kontroll Apparat
0.1/5

€ 672.13

hot
CS Unitec
3.4/5

€ 221.18

CS Unitec
3.4/5

€ 221.18

hot
Primefit BG1003D-7 Blow Gun 7-Stéck Kit
3.4/5

€ 22.19

Primefit BG1003D-7 Blow Gun 7-Stéck Kit
3.4/5

€ 22.19

Entdeckt eisen internationale Netzwierk

Mir schécken an 28 Länner, iwwer 200.000 Produkter. Bleift aktualiséiert, abonnéiert Iech op den Newsletter.

Array